Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
hi,
first of all i need to say, i am very happy to found the s120 softdevice where we can implement the client role also
i downloaded new alpha version of s120 softdevice...
hello,
i am using s120 softdevice along with nrf6310 mother board, the problem is i am dumping the code into the device, but i am having doubt how to verify that it is...
Hi, I am creating a PCB design and am not sure if I should connect the pad under the nRF24L01+ to the ground plane with a couple of vias.
The data sheet says it should...
Is there a plan to support the BLE central role in the software stack?
As it is now, I absolutely cannot use the nRF51822 since the S110 stack does not support operating...
The attached test program and logic analyzer displays shows that the function twi_master_transfer() returns to the calling program before the transfer is complete, if TWI_hw_master...
The error I get is app_error_handler 0xDEADBEEF, 360 (line number), src\ll_lm.s0.c
This is with SD 5.2.1
With SD 6.0.0.1-alpha, sometimes I get
app_error_handler...
Does anybody know of any plans to combine the Peripheral and Central roles into a single SoftDevice?
The killer application that this provides is the ability to create...
Hi All,
I use nrf51822 transfer data to nrf uart app for android,when I use following parameter ,the device and nrf uart app work well.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS...
I'm interested in advertising with data type 0x18 random target address. I found a post for advertising with 0xFF manufacturer specific data. What changes are necessary for...
Hi,
I am using bluez 5.12 and am having difficulty connecting to an nRF51822 EK running the Health Thermometer application and Soft Device S110v6.
I am able to see the...
Hello,
I cannot build a known-buildable project and get error A1023E.
No Programmer's Reference exists and there is no documentation referencing this error.
I think...
I want to quickly transfer data between nRF51822 and celluar phone. The data rate is 100 packets/sec. Packet size is 14 bytes. We know mouse can reach almost 200Hz report...
can i use j-link debug probes to program and debug evaluation kit?
recently i bought J-Link debugger from the segger, i tried to find the pinout of the SWD of the eval...
I see that the source code of app_gpiote.c uses NVIC_... functions to handle the interrupts:
app_gpiote_init.c, line 160...:
NVIC_ClearPendingIRQ(GPIOTE_IRQn);
NVIC_SetPriority...
My question is regarding the adertising with the softdevice on the heart rate sensor example.
My starting point is the following:
I connect PCA10001 / PCA10000 from...
