Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
First I'm new to these devices and BLE in general.
I am however very experienced at embedded design and Keil tools and ARM processors.
I have got the demo heart beat...
I have the ble_app_hrs communicating with the ble_app_hrs_c, and everything works OK. However, I have to be able to send data in both directions. How do I modify, or what...
I am developing a device converting adc input into data and transmitting them and receiving them at other place,I cant figure out between analog input eg:AIN0 and the port...
Hi,
I'm using nrf51822 with s110 softdevice v6
My question is the following.
How many devices sending advertising messages can be detected at a time by a central unit...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi All,
I am trying to run the uart example that comes with NRF51822 development kit. I've set up the mother board (nrf6310) according to the sdk doc and have flash the...
Dear Nordic Developer Zone,
I am using nRF51822 with softdevice.
I don't understand very well the advertising mode "whitelist".
My target is to be able to connect...
Hi all!
I'm running my code based on example "ble_app_template". When advertising without doing anything else, the current comsuption is about 200 uA.
Then I added a...
Hi,
i just started again working with nrf51822 but now with eclipse+gcc and with new soft device S130.
I am struggling with the addresses of flash and ram. I want to...
I have been working on porting my code from Keil to gcc because it has grown larger than the 32K limit that the free version of Keil allows. I am using the s110 softdevice...
Hello, I have a problem during first programing PCA10003 blinky_example. I get an error:"Flash Download failed - "Cortex-M0" "
Keil v4.74
SDK v6.0.0
In nRFgo Studio...
I've been trying to get the SDK softdevice ble demos to work on a mbed board. I'm using pyOCD+linux. I can compile and flash elf (.out) files in gdb with 'load' and I can...
