board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hi,
I am porting a SDK 2.6.0 project to SDK 2.9.0. It gets built without errors but when I try to run it after flashing I get the following.
I am not sure where to start...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
I've developed a custom Matter application based on the Matter samples in the Nordic Connect SDK, targeting the nrf52840. I developed the first version using the nrf52840dk...
Dear Nordic Semiconductor Support Team,
I hope this message finds you well.
I am currently evaluating the nRF52840 for use in an industrial/automotive application and...
Hi Nordic team,
I’m currently testing UART communication on nRF54L15 with NCS 2.8.0 , and I’ve encountered an issue I’d like to ask about.
When using UART20 configured...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
I tried running the " Bluetooth: nRF Distance Measurement with Bluetooth LE discovery " case in the SDK, here is its link： Bluetooth: nRF Distance Measurement with Bluetooth...
Hello,
I'm trying to connect a BMI270 sensor over I2C using Port2 on the nRF54L15 , with the nRF54L15 DK , and I'm working with the nRF Connect SDK v2.9.0 , based on a Zephyr...
Hello,
I have the nRF7002 DK, which includes the nRF5340 (App + BLE cores) on-board.
The hardware requirements do not list this DK as usable for the course, which seems...
Hello,
I am currently designing with the nrf52840 and trying to implement the 32 MHz crystal required for bluetooth radio operation. The calculations for the load capacitance...
Hello,
I am attempting to build the Matter template using only the nRF54L15’s internal memory. While the build occasionally succeeds, it more often fails, and I am unsure...
The nRF52832 devices have been produced in hundreds of units. Currently, it has been found that individual central devices are problematic – connecting to peripherals often...
I have enabled all the dependencies asked as below
CONFIG_IMG_MANAGER =y
CONFIG_STREAM_FLASH =y
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_DFU_TARGET_MCUBOOT =y
Still...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
