I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hi,
We are currently testing the fuel gauge firmware from the nRF Connect SDK but are encountering difficulties integrating it with the u-blox B206 module. Could you provide...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hello,
I am looking into the market for PMICs for 3V primary coin cells, for use in (somewhat) remote IoT devices.
It is exciting to read about the new nPM2100. I already...
Hello, With respect to my previous post, I am trying to use the nrfx_pwm_simple_playback function to run sequences continuously for an RGB led. Initially I did not fully understand...
Hi
I ve to use nrf pwm common mode feature, and there is sample code under project name common_mode_test, but i am unable to build it either with ncs version 2.9.1 or 3...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
We used nRF5340 as the controller to develop a product for our customer, which requires a QSPI interface of 5340 to drive a screen. However, during testing, we found that...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi,
I am currently making an upgrade og a nRF51422 project that has both BLE. and ANT+ Cycling Power profiles and if I run the old project on an 51822 processor I can see...
Hi,
I try to migrate a working nRF53 Zigbee project from SDK 2.7 to the latest SDK and an nRF54. As described here, I also switched to Zigbee R23. The project structure...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi,
We are interfacing WM02C (nRF7002) with LPC55S69JBD100E as the host controller.
1. Could you say how to select the 2.4 GHz and 5 GHz antenna selection by hardware...
Hello, we are using a BLE module nRF52832 (MDBT42-P512KV2).
We also add the external 32768Hz crystal to our application with this module.
However, we recently found that...
