Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
Im trying to send 20 packages of 30bytes each as fast as possible, so I created the following loop:
for( pack=0; pack<20; pack++)
{
w_tx_payload_noack(30, MegaBuffer...
Hi all,
I have a custom board with the Nrf51822 BLE chip and it works in broadcasting mode without connection only. Basically it sends the advertising data on an established...
Hi
I have some problems about using your Master Emulator API. I want to write a dynamic link library with C++, but I don’t know how to invoke the MasterEmulator.dll.
The...
I'd like to use LPCOMP. I'd like to get rid of the 12K pulldown on SWDIO.
I can tell from PCN-082 that QFAA CA and C0, as well as QFAB AA and A0, will let me do that. ...
hello,
I know the ble device ,have central and peripheral and have some name(server/client and Observer/ Broadcaster).
The peripheral(server) has data that is needed by...
I put the boot loader at 0x3a800 and the application at 0x27400. the region from 0x14000 to 0x27400 is all blank (0xff). also
nrfjprog --memwr 0x10001014 --val 0x0003a800...
Hi,
I need to pair with the master after pressing the button in my slave device, instead of asking for passkey. Through the master control panel, i can able to see that,...
Hi,
Actually in our application we have connect accelerometer sensor to Nordic by SPI. I'm calculating power consumption for it. In datasheet it's mentioned for SPI Data...
Hello to everyone,
My problem/question now is about the MasterEmulator. I´m working with the nRF51822(SoftDevice) and i have my own program already working more or less...
Hi
I am a newbie to the bluetooth technology. I want to ask some questions:
How to apply a LLS(lost link service) profile to a bluetooth module?
Can I buy the...
After reading devzone.nordicsemi.com/.../is-there-any-differences-between-nrf51822-and-nrf51922 and the literature around nRF51922, I'd like to know if there's going to be...
Hi,
I've developed an application which sends sensor data through the BLE interface at maximum available bandwidth by checking the BLE_ERROR_NO_TX_BUFFERS return value...
Hello,
I was wondering if anyone has had success communicating with the nRF24L01+ eval kit and a Raspberry Pi. I have found several examples through Google and am trying...
I am requesting the softdevice to start/keep the 16Mhz crystal oscilator running with the following code:
// Request 16 MHz crystal oscillator
err_code = sd_clock_hfclk_request...
