FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hello,
I'm working with nrf51822 on a custom board and i'd like to use the LPCOMP as wakeup source. I configured the module by the code listed above:
void lpcomp_init...
So now that I understand the problem with overlapping asserted events on the GPIO port, I can't figure out the correct way to reset the sense field in the GPIOTE_IRQHandler...
Hi,
I follow steps in User Guide version 1.2. The Blinky project is working fine.
Then I program SoftDevice and after than compile and Download HRM using Kail
But led...
now,i pairing my peripheral and Communication read/write data. but have some issue for disconnect/reconnect .
1.disconnect: when i disconnect (call didDisconnectPeripheral...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
I am developing a windows application, using the MasterEmulator api.
I am discovering BLE devices with scan parameter Active and Passive.
The result is that most of the...
HI,
when I used nRF51822 for 2.4G transfer ,I found that RX can't receive data in some direction .Can TX use two antennas and matching networks to work alternately in order...
Hi all,
I am currently working on a BLE project based on the PCA10001 evaluation board. I am trying to follow the nRF51 application note. I have done everything that the...
Hi
I'm using the nRF51822 and custom a service.I add 4 characteristic in the service and all of them
config to indication type to send data.Everything is Ok and sending...
Hi
I'm just starting with all this. My set up is a nRFgo motherboard with a nRF51422 DK attached (PCA10007).
I've installed all the tools of the toolchain as stated in...
I've just flashed the softdevice 5.2.1 and BLE Proximity sample app to my nRF51822. I presume any previous bond state on the device should have been wiped by doing this. ...
It would be nice if you could update Application Note 29 ("Development with GCC and Eclipse") for the nRF51822 to include instructions for Mac OS X.
I don't think it's...
