Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I updated the "ble_app_proximity" PCA10001 example for adapting the time constants of my needs.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(3700, UNIT_1_25_MS)...
hi,
In my device(nr51), have multi service and one client.
when i initial the client first ,then to setup service. this follow is O.K.
But, if i initial the service, and...
Keyboard source: Desktop 2 v1.0.5
Dongle source: 1. Desktop 2 v1.0.5 dongle hex; 2. Desktop 1.2.2.293 dongle hex
I found it is very defficult to pair the keyboard with...
Hi,
1. I have some puzzles,please give me some explanations,thank you!
In my design,I use some 51822 devices as tags which can communicate with the host.
The tags can send...
Hi, I want to know what's the differences between the NRF_CLOCK_LFCLKSRC_RC_250_PPM_xxMS_CALIBRATION and NRF_CLOCK_LFCLKSRC_XTAL_xx_PPM where xx means a decimal number.
when...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi,
I want the NRF51 to respond to a received packet from a particular device using register TIFS to control the interfame timing.
For TIFS to work I have to set the...
Dear Nordic,
is it possible to build a simple data bridge at speed of 115200 and up based on nRF51822 with CTS/RTS support and a fixed pin code for nRF51822 pairing?
I am working on a multi-node network application with multiple transmitters and receivers and I have a question about timing for chips like the nRF24L01+. I would like to...
Hi
In my case i have gpio interrupt for every 25ms. so i change button detection delay t0 10ms.
and i given timeout in all while loops of twi_hw_master.c.
but my...
Hi,
we have nrf51822 custom hardware.
we are flashing application through j-link.
but after every flashing , i need to do switch off and on the device.
then only...
I have no power on my nrf6350 display
I programed the board with the display jostick example but cant see nothing on my lcd of the nrf6350
any advice?
thanks
...
Hi:
I'm fresh in use BLE.
when i installed SDK, i could not install the lastest version v4_4_1,but can install v3_0_0.
My system is MS win XP Pro SP3.
Please tell me what...
hi,
i took the same example of BLE_LBS, as it is working properly in case of writing to the device, but when i implemented my own for writing to the server, it is not working...
