Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Dear developer zone,
I am using nRF51822 with soft device and SDK 4.4.2
My device return an error on disconnection when the ble_bondmngr_bonded_masters_store function...
Hello,
I want to test my circuit using a CR2032 coin cell. Is there any way to jumper a coin cell into the supply on the nRF6310 and bypass the voltage regulator/RS232...
Hi,
I am curious what is the main difference between nRF8001 and nRF8002.One is for connectivity and the other is for proximity. However, I would like to develop an application...
i need a help with the attenna design. here is the eagle files, i'm not sure it is fine. i used a Balun BAL-NRF01D3 and my board thickness is 0.6mm. i need to know the copper...
I got the nRF51822 DK and tried hooking up the dongle. I am using Windows 7 32 bit. When I plugged the dongle into a USB port, there is a “JLinkCDCUARTPort（COM19)” added to...
Hi,
My device is always in bootloader mode, even if i flash the sample heart rate application it is not entering into the application. Actually, before it was working fine...
Hello,
I am planning to develop an application in which I need to do some image processing (probably using open CV libraries), and I would like to know if the nRF51822...
I see in the example code there is
#define FLASH_PAGE_SYS_ATTR (BLE_FLASH_PAGE_END - 3) /**< Flash page used for bond manager system attribute information. */
#define...
I'm using NRF51822 and I have some question about the ble connection:
according to BLE 4.0 spec, when Tsup(connection supervision time) reaches, connection lost is considered...
Hi
Do the latest sample apps (for example, Heart Rate) which do not required bonding behave as follows:-
make connection from iphone
enable notification
check...
We have done some test on how fast we can receive data from a BLE service, which is around 6KB/sec and this is all fine. This test was fairly easy to make, as we could just...
I have implemented my own I2C driver and I am getting issues with NACKs.
On review my code is doing what twi_hw_master.c is doing.
I then went looking for a Nordic sample...
We have developed and certified a module which uses the nRF24l01+. We spent a good amount of time tuning the antenna circuitry which has resulted in very good range... in...
Hi,
how to get into the bootloader mode without pressing any button, when some application is running? I also tried it with setting the NRF_POWER->GPREGRET but it is not...
