Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi ,
I am using PCA10001 board.
Now i want create 4k buffer in RAM. Which is good way allocate memory to 4k buffer.
Can i use dynamic(malloc function) or static memory...
Assuming the system is composed of one device using nRF51822 and iPhone/PC,
If we want nRF51822 detectable by iPhone/PC so that iPhone/PC can connect nRF51822 when they want...
Hi!
I have been using Bluetooth 2.0 modules for years and now I want to take the step to 4.0/BLE. Previously I used Free2move modules with built in stack. Very simple, make...
I have the nRF51822 development kit (with the new hardware revision QFAA or something), and I am using the Master Control Panel with the new 0.9 firmware for the dongle. ...
Hi in my case,
i pressed gpio button for one time it will do one event.
and for double press it will do another event . how can i do this one,
Regards
Balaji
Hi
In my case i have both 3 gpio interrupts and 4 rtc1 interrupts and have some timer 0 and 1 interrupts
also. how to set priority for all these interrupts in both while...
Hi Guys,
I am planning on using the nrf24l01+ to send data with a payload which is larger than 32 bytes, I was wondering whats the fastest way to transmit these packets...
Hi,
In the nrf51822 SDK examples, there is an example of radio_example which is used for send data and read data. I want to konw that if one module send data and then...
Hello - I am trying to port code over from a development kit over to the WLCSP nRF51822 on a custom PCB.
I am able to connect/bond with my device fine, however I am having...
Hi,
we're using an nRF8001.
Trying to find the relevant Bluetooth Specifications, we found the following mess (pardon my french!):
Core Specification 4.0, 2300 pages...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
nRF51822_Development_Kit_User_Guide_v1.3.pdf document has table 6 which indicates SoftDevice A and SoftDevice B. DK includes s110_nrf51822_5.2.1_softdevice.hex. Is this SD...
Hi,
I'm testing a BLED112 USB Dongle from Bluegiga ( www.bluegiga.com/.../).
I have not been able to use see the Nordic Board advertising. Currently testing ble_app_proximity...
I was wondering would it be possible to use a 50 ohm IC Antenna ( like this one ) for the nRF51822 with the matching circuit given for the nRF24 ( link here )?
It seems...
