i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi All,
I use nrf51822 transfer data to nrf uart app for android,when I use following parameter ,the device and nrf uart app work well.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS...
I'm interested in advertising with data type 0x18 random target address. I found a post for advertising with 0xFF manufacturer specific data. What changes are necessary for...
Hi,
I am using bluez 5.12 and am having difficulty connecting to an nRF51822 EK running the Health Thermometer application and Soft Device S110v6.
I am able to see the...
Hello,
I cannot build a known-buildable project and get error A1023E.
No Programmer's Reference exists and there is no documentation referencing this error.
I think...
I want to quickly transfer data between nRF51822 and celluar phone. The data rate is 100 packets/sec. Packet size is 14 bytes. We know mouse can reach almost 200Hz report...
can i use j-link debug probes to program and debug evaluation kit?
recently i bought J-Link debugger from the segger, i tried to find the pinout of the SWD of the eval...
I see that the source code of app_gpiote.c uses NVIC_... functions to handle the interrupts:
app_gpiote_init.c, line 160...:
NVIC_ClearPendingIRQ(GPIOTE_IRQn);
NVIC_SetPriority...
My question is regarding the adertising with the softdevice on the heart rate sensor example.
My starting point is the following:
I connect PCA10001 / PCA10000 from...
Hi,
we are interested in the combination of the nRF51822 with a sensor board which was announced in October but since then there were no updates and I can not find any other...
Hi
We know most of access contol for entrance was implmented by RFID. Is it feasible to design it by BT4.0? My idea is as below. Thanks for your comment.
There is a...
Hi.
I have a nrf51422 EK. I follow the steps in nrf51422_Evaluation_Kit_User_Guide v1.1.pdf but I couldnt do blinky_example project to works. In debugger mode, I see that...
I'm using the rRF51 DK with Segger Jtag. In the demo Keil version, I set up Segger jtag to NOT cache memory. When I look at a memory view in Keil, the memory is not being...
Hi
I tried DFU OTA in nRF6310 board as SDK document guided but it cannot work.
Boot loader is from SDK5.0.0 device_firmware_updates project..
SoftDev is v6.0.0....
It appears that the current version of Master Emulator v3.5.0 does not include support for long-writes. I know that SD110 v6.0.0 does support long-writes and my application...
Chip: NRF51822
softstack version: 5.2.1
I ran into an issue and i'm trying to understand it better. I was calling the function sd_ble_gatts_value_set(...) from a GPIOTE...
