I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi All,
In ble_app_hrs example two function is defined for gpiote_init()
1)
static void gpiote_init(void)
{
APP_GPIOTE_INIT(APP_GPIOTE_MAX_USERS);
}
2)
static void...
Hi
I found there is bonding managing routine in SDK HRM and Proximity examples.
bond_manager_init();
It means in these two case, after pairing with BTLE host, the...
My question is regarding the PPI channel groups. The documentation is extremely limited and leaves many questions.
My goal is to generate 3 PWM signals from a timer with...
If i understand tasks are for outputs and events are for inputs.
Wanted to know relationship between channel and the pin numbers. do they hold the relationship like...
Hello,
I am really confused on how to get a custom BLE service up and running. I have read through nAN-36, and compared the suggestions in that document to the HRS example...
In nRF51 reference manual v2.1 section 18.1.1, it mentioned that the RTC must be able to
run while the 16 MHz system clock (SysClk) source is OFF. 2 questions :
Q1: Since...
Hello,
I'm trying to get the SDK examples working in Eclipse. I have followed all steps(except debugging part) in the nan-29, but i can only import the s110/ble_hrs example...
I am looking for the spacing in mils or mm between the two samtec connectors on the nrfGO board. I am making my board to interface with the PCA10005/PCA10004 and I would like...
Hi,
I'm new to nRF8001 SDK and Bluetooth and I hope my questions are not too stupid lol. So here it goes:
I'm using the Nordic nRF8001 SDK to implement a self-defined...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...
Hi all,
when i want to connect different peripheral on central(s120).
it have a error and disconnect.
it seem ok , but that will disconnect later.
ant it get disconnected...
