hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
I have only nRF51822 DK without starter kit motherboard. how can I download softdevice(S110 Bluetooth low energy stack) to my nRF51822 chip in the Keil environment?
...
Hi all,
the release note of SDK 4.3.0 reports that it was tested and verified using BLE S110 version 5.2
When it will be available (version 5.2) ?
Actually we can download...
Hi,
I want to read the data by the radio.now I have read the temperate data from the tags by 51822. the data include the ID value and the temperate value. the ID is hex ...
Hello,
I'm working with nrf51822 on a custom board and i'd like to use the LPCOMP as wakeup source. I configured the module by the code listed above:
void lpcomp_init...
So now that I understand the problem with overlapping asserted events on the GPIO port, I can't figure out the correct way to reset the sense field in the GPIOTE_IRQHandler...
Hi,
I follow steps in User Guide version 1.2. The Blinky project is working fine.
Then I program SoftDevice and after than compile and Download HRM using Kail
But led...
now,i pairing my peripheral and Communication read/write data. but have some issue for disconnect/reconnect .
1.disconnect: when i disconnect (call didDisconnectPeripheral...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
I am developing a windows application, using the MasterEmulator api.
I am discovering BLE devices with scan parameter Active and Passive.
The result is that most of the...
HI,
when I used nRF51822 for 2.4G transfer ,I found that RX can't receive data in some direction .Can TX use two antennas and matching networks to work alternately in order...
Hi all,
I am currently working on a BLE project based on the PCA10001 evaluation board. I am trying to follow the nRF51 application note. I have done everything that the...
Hi
I'm using the nRF51822 and custom a service.I add 4 characteristic in the service and all of them
config to indication type to send data.Everything is Ok and sending...
