Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Having some issues with the examples on the nRF51822 development kit. Hoping someone can help.
Working from nRF51822_Development_Kit_User_Guide_v1.3.pdf.
Motherboard...
Hi all.
I am making a PCB for nRF51822. My PCB need is to talk with iPhone for BLE Proximity application. Also I need to control a LED from iPhone. And I need to get low...
In short: Is it feasible to use RSSI values when tuning the antenna?
I have a custom board with an nRF51422 on which I have designed the RF part to be as much as possibly...
Any suggestions for handling a bricked custom board?
I'm pretty sure I know where the problem is in my code, but now I can't reprogram the board. I did have this happen...
Hi, I'm developing an BLE application using nrf51822.
I have a BLE security issue to discuss.
(Actually I don't have much network security background...)
In our application...
I'm using PCA100001 board with pure-gcc Makefile and s110_nrf51822_5.2.1_softdevice.
And I'm writing simple code customizing s110 samples like below:
static void ble_stack_init...
Hi
Does the NRF51822 support ANT and where would be a good place to understand how to implement ANT ? I also want to know where I can get more information regarding the...
Hello community, first time posting a question so please try and forgive any future mistakes.
anyways im new to using the keil IDE and am have some problems. I have dug...
I am using pca10001 board and started my development from nrf6310/s110/ble_app_hids_keyboard.
SDK version is 6.0.0. I have successfully tested my device with (MCP) Master...
Hi,
I am very new to BlueTooth technology. Currently i'm testing the nRF51822 evaluation kit to see if the BLE module can be used for a specific project. I've tried several...
I have a schematic in which Balun is connected as a matching network to Ant1&Ant2 pins making the output impedance 50 ohms. Now i want to connect an Antennae to it which is...
Pages 51 and 53 of the nRF8001 Product Specification (v1.2) show a reference design for a balun network in which capacitor C4 is listed with a value of "N/C". The component...
Just in case no one has ever given any feedback WRT Eclipse, Id like to be the first. My experience is using it with all the features for a NRF51822 project, and it kind of...
Seeing, that the nRF51822 was specified to operate with a 16 MHz crystal or oscillator. Is that also the clock what the Cortex-M0 core runs or is there a PLL to increase the...
Dear Support Team,
I'm working on a BLE application and the most stuff works well but now I had a spurious application crash at "src\ll_lm.s0.c: 1038". Could you please...
