Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi, If I understand correctly the debugger on PCA10040 can operate in 6MHz/n as SWO frequency.
the nrf52 can operate at 4,8,16,32MHz swo frequency.
How are we to use SWO...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I'm trying to implement the DFU Feature into my application, but it seems to be in a bootloop after it starts advertising.
The application works fine when flashing it via...
Hello everyone, I want to measure Low power mode current consumption in nRF52 DK,but I dont have accurate CRO to measure in micro Amperes, therefore I would like to know if...
the eclipse build memory map is
text data bss dec hex filename
363312 2485 5340 371137 5a9c1 ********.elf
363312 2485 5340 371137 5a9c1 (TOTALS)
it is giving very large...
Hi Friends, I like Nordic and Arduino, it's great if Nordic can support Arduino officially, we can use the ARM0 in Nrf51822 as a single control point of Arduino project. There...
I taken the Android-nRF-Beacon-for-Eddystone app code from github.
From my account I configured my Google Dev console:
enabled proximity API
added credentials...
Hi all,
I followed the tutorial listed below:
devzone.nordicsemi.com/.../
I want to use SEGGER_RTT_printf but I always get this error:
Error: L6218E: Undefined symbol...
Hi,
I am working on one project in which I want to connect my two custom borads with S130 softdevice but I am not able to do that. My custom board has nRF51822 chipset...
I would like to implement a simple code to use SAADC on NRF52 to sample one channel at maximum sample rate (theoretical 200KHz).
All the examples I have found use limiting...
Hello All,
At a time either ble nus or dfu can work.
I have an problem with the services ble nus for uart and dfu does not work simultaneously means if i am adding both...
Hey, I got 2 beacons which I have connected via BLE successfully however I have some problems with BLE_GATTC_EVT_HVX event. Every time I get only one BLE_GATTC_EVT_HVX event...
Hello,
I measured the current consumption at 0 dbm of the app beacon example.
During the TX send phase I measure a current of more than 11 mA. Thats too high when I compare...
