Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Dear Nordic Team,
Thanks for support.
I want to know the possible for voice file transfer to over BLE. I am using BR281 audio detection on semiconductor. I want do the...
I'd like to retain a few bytes after a restart from system_off. I know the GPIO state is retained, are there any other registers other than that? It looks like RTC1->CC[0...
I've been struggling for some time to get L2CAP transfer between an NRF51822 and a Linux machine using bluez.
I've successfully created a connection between the central...
Hi,
I want to understand ANT and want to begin development with ANT once I figured out how it works. After reading posts on this forum I found out that not all Softdevice...
Is there an example for using a 10 pin 2 digit 7 segment display similar the picture below?
It is common anode and actually has 10 pins (pin 2 is the DP or decimal point...
Hi,
I was wondering about that I did not found any information about dedicated pin usage.
I am using I2C/SPI and UART and did I understand it correctly that i can use...
My application has two firmwares with different offset addresses. One firmware sitting at 0x16000 and second one is at 0x25000. I want jump to the second application from...
I have an issue where after transmitting a radio package, is setting up the radio as receiver, get indication for reception (have indications for ADRESS and PAYLOAD events...
I programmed my beacons with ble_app_beacon (nordic firmware). android can locate my beacons without any problems.
I installed nrf connect app, it can find them too.
but...
Hello,
I'm using BLE, RTC and app_timer to blink a led.
I blink the led 10 times when I receive an order from BT (by means of NUS), and then by means of RTC.
uint32_t...
Hi. I'm very new to this so I hope you'll forgive me for my basic questions!
I would like to take data from multiple ANT fitness devices and send it to an iPhone application...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and i have chosen mono-pole antenna is a good choice,because...
I Programmed my beacon devices with this firmware:
ble_app_beacon.zip
the only app that can find my beacon on ios is nrf connect. in this firmware the uuid is this:
...
