Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Do I need to manually go though every HW exaple in the examples in sdk12 and cut and paste all the little bits that I need or is there any other way?
I have a custom board...
Hi,
I'm using the nRF52 as a master and an external RF chip as a slave. After configuring my spi bus using nrf_drv_spi_init(&spi, NULL, NULL), in my main loop, how do I...
I have used nRF toolbox to update bootloader and firmware to my nordic device. I was previously using iOS9 (I believe 9.3.5 - whatever the latest version was before iOS10...
Firstly,I used ios9.3.5 to DFU successfully,
But when 9.14(ios10 was pushed),then my iphone6s was updated to ios10,
finally DFU failed.
The device can enter in the DFU...
Given this answer , do the BLE_GAP_CONN_SEC_MODE_SET family of macros only relate to the Write permissions of the device name?
Maybe a better way to ask this is: Is it...
Hi,
I am referring nRF5 SDK for Eddystone ( github.com/.../nrf5-sdk-for-eddystone) .
Here GCC Makefile based projects are scheduled for a future release.
I am trying...
Hello,
sorry for the dumb question but do you know which software does Nordic use for creating/editing sequence charts like the one in the documentation?
infocenter...
Hello,
I am currently working with NRF openmesh but when I try to set a new handle i get an error. This is what I tried.
uint8_t ledje = 0x01;
rbc_mesh_value_handle_t...
Hello,
I am doing bluetooth transceiving test. About in 10 times of transceiving wtih App, I got 9 times success, but one time failure. From my observation, App and bluetooth...
I evaluating nrf52_dk board, to build an application with custom BT Service on the nrf52_dk using the mbed platform. I see the new platform nrf52_dk platform is available...
Hi!,
I'm working in a Android app to communicate with a nRF52/nRF51 boards.
I've been using Bluetooth Smart nRF51822 Beacon Kit.
But I think what I need is not possible...
How do I change the properties of the Generic Access service's "Device Name" characteristic to be Read Only, not Read and Write? I see this
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
Hi,
We are sending data every connection interval which is a stream using the API sd_ble_gattc_write. Whenever there is a dropped packet from what we understand, the Softdevice...
I used SDK11, SD332, and no change anything.
the application reset as picture.
can you test this issue and give suggest ,why app reset?
D:\work\nordic\BLE\SDK\nRF5_SDK_11...
