Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have been working on "merging" SDK for Mesh's lightswitch client example and SDK v14.2.0 UART server example, mostly following the document on this site , with some changes...
I've gone through the user manual for the Nordic Power Profiler Kit, but I can't find any basic information on how to understand the plots and the measurements reported under...
I would like to have one central and two peripheral connection. Ad functionality required is same as NUS UART Example. But the example code connects to only device. Can any...
Hello,
i would like to connect two Redbearlabs Nano v2 just with eachother. The central one connects just to the peripheral, but the peripheral is still open for every...
Hello There,
I found following dongle based on nRF51822.
They claim same will work for bluetooth 5.0 also.
I know BT5 devices are not backward compatible, so not sure if...
Hi,
How can I share a GATT server profile constructed on nRF connect for PC with nRF connect for Android ?
'Save/Load setup' on Windows PC stores/Load json file
In...
I've got a set of boards that are behaving very strangely. I attempt to turn on the HFCLK but the HFCLKSTARTED event never comes nor does the HFCLKSTAT register indicate that...
I cannot suffer this tool anymore. As u can see in the pic below, it provides a cursor mode to measure the currents of X1/X2. However, users always need to know the average...
Hi,
I want to connect 4 antennas to nRF52832, they respectively points to North, South, East and West direction.
Also I hope the nRF52832 can do switch antenna job,...
I'm trying to use gcc and eclipse but I'm getting an error in eclipse that certain variable names cannot be resolved. I know that its not being able to get the variable names...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
Hi,
do sd_flash_page_erase or sd_flash_write provide any guarantees that the command has executed successfully or should I do a manual check to verify if the page was really...
Hello all,
I am working on nrf52832 Board and i want to use it as translator to send and receive the data , please tel which pins i need to select as UART(rx,tx) pins ...
I am designing a custom board with nRF52840, powered by USB, no battery, using its internal LDOs to supply other peripherals with 3.3V
I have two questions about pins/outputs...
Hi
I generate a pwm signal via changing the state of one characteristic. In general, the pwm works fine. But the problem occurs when I add the timer which is responsible...
