I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
I made a board without external 32kHz crystal.
So, I changed NRF_CLOCK_LFCLKSRC source to NRF_CLOCK_LF_SRC_RC, which is used in ble_stack_init.
Now, I need to make DTM...
Hi,
I am use Exclusion list for my one application.
Exlusion list work is ok,but i am facing problem for how clear Exclusion list ?
My Controller: nRF514222 Rev 3,...
This is my first time working with a microcontroller and working with C as well, my only previous experience being C++ done in notepad on Linux. Currently I'm trying to just...
To reduce nRF52 design thickness, I'm planning to use a low profile inductor on the DCDC converter.
The low profile inductor has a higher resistance, compared to the recommended...
Hi, All.
Once I wrote data in NV memory, it's OK. I can get the same data I put in.
But, after power off - on reset, data are invalid. It's all 0xff(erased state).
I used...
Hi,
I have been trying to do it and even though I have generated packages using the old nrfutil and the new 1.5, when I use nRF connect to do the upload it aborts without...
I programmed my beacon with this code:
ble_app_beacon.zip
I use nrf connect app to see its signals. nrf connect can find my beacons but it says:
serviceUUID : N/A
TxpowerLevel...
Hi all,
I believe it should be possible to defined a characteristic which can be written to but have no automatic write response ACK sent. Instead I want to send a manual...
I develop a temperature sensor sending a temperature and battery status every second.
Used to work fine on previous nRF Toolbox.
Today on my Android 6 and latest nRF Toolbox...
Difficult to obtain the high-ohmage resistors in the solar beacon reference design. Will 5% resistors suffice or do the resistors have to be 1% tolerance.
I have difficulties understanding the COMP APIs, this function below starts after initializing the COMP the peripheral.
nrf_drv_comp_start(NRF_DRV_COMP_EVT_EN_CROSS_MASK...
I am using the nRF51822 utilizing the internal LDO setup. I received a question during regulatory submittal that I am not able to answer and am looking for help on. Is the...
Hi
I've tried to update some of our environment to the SDK12 files. When I tried to compile some of the files a weird bracket error showed up.
At the end i could find...
Hi,
I'm trying to run one of the template app programs from the Nordic SDK 12.0 library with a nRF52832 board as my target. I had trouble with compiler errors using the...
