When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I am trying the ANT-OTA DFU Update using two nr51422 pca 10028 board. One is sending Transmission messages in the CHANNEL_TYPE_MASTER mode, while the other is receiving Messages...
Hello, I'm a beginner for nRF51822, now my status is sticking on those SDK_11.0.0 BLE examples, while I could successfully running non-BLE (such as examples of bsp/uart)....
ElfApp.zip This attached application is based on Nrf_uart demo app.
It works fine under Android 5.0 and 4.4 smartphone. When I click the connect button, it shows the info...
Hi,
I'm on the project where I use SoftDevice s132 on my own devBoard with nrf52 chip.
I know for Connection Interval and other parameters that determin BLE communication...
I am using nrf51822 as a central device that is trying to connect a peripheral device nrf8001.
I want to build communication bewteen them and use nrf51822 to receive the...
Hi,
I have a small question regarding flash write/erase cycles and I was unable to find a clear answer.
I can see in NRF52 specs:
Flash write/erase cycles: 10...
Hi,
I've been trying to get DFU updates working on my device for a while now... I've got the single-bank bootloader compiled and seemingly working (and a combined hex file...
how to modify ble hand shake time which normal connect to phone.
this scene the ble board has connect to the phone, but need down scoping the ble time to let the 2.4G work...
Hi,
I would like to save some data from characteristic into the Flash. Due to this fact I decided that I will use scheduler. When the value of actual characteristic is...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS)
against the Bluetooth Test Specification (Document Number CPS.TS.1.1.0).
We fail the...
Apparently, the dfu bootloader example in nrf51 SDK 8.1 is not working on PCA10031 type(16K RAM devices). In my case, the device is RedBearLab BLE Nano and nrf51822.
Can...
Hello,
because of my mistake, rx tx pin was not cross connected.
So i want to swap rx tx pin on nrf51822.
In the example ble_app_uart_s130_pca10028, i change the code...
I used the example in nRF51_SDK_9.0.0_2e23562\examples\dfu\experimental, the first time that work well. But when I want to update a app in app(with dfu function),it failed...