Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When a callback function is registered via the softdevice_ble_evt_handler_set(), are there re-entrancy issues when the callback is called by the softdevice?
For instance...
HI,
May I ask question ?
I am testing the "ble_app_hids_mouse" program . When I run the program ,but it can't pair with my computer(windows 8.1).I don't have the nRF6310...
I want to connect my mouse to win7 or XP PC(but I can only buy CSR BLE dongle CSR8510A10),
It connect OK in win8 with the same dongle but report error as the title describe...
Hi,
I have a problem is that I use the 51822 as a reader to read the 24l01's radio data.Now,I use the UART to read the instruction from the PC. If the instruction is "ON...
Hi,
I use the nrf51822 to read the data from the tag which designed by the 24l01p radio module.In the whole progress, first of all, the reading module read the instructions...
I have interfaced nRF 8001 with Arduino through MISo,MOSI,SCK etc pins and it is connected successfully. When i connected my arduino with pc, i thought nRF 8001 will start...
I'm trying to make a simple BLE app based on LED button demo (BLE_LBS.C) that probably don't use much resources. I added FIFO UART communication routines and when I tried...
I have an NRF 8001 BLE chip, can you provide the break out board schematic to make this chip discoverable to my iPhone 5 as soon as i power that break out board. And how to...
Can anyone tell me how to connect NRF 8001 with Arduino mega 2560. I have developed an iPhone application and just want to connect with NRF 8001.Please tell me how to connect...
OK, probably a dumb question:
The nRF51822 reference manual indicates that the RTC is driven by an external 32 KHz input. Can anyone confirm whether it will or will not?...
Hi
can you please help me convert these Keil pre processor calls to something that gcc compiler can . If possible i would like more information about these calls and the...
I'm using Nordic NRF51822 and the Segger JLink with the s110 Bluetooth stack active (correction: flashed on the chip, see below). When my code hard faults (say due to a dereferencing...
hi, I currently stuck in the follow section:
static void gpiote_event_handler(uint32_t pins_low_to_high, uint32_t pins_high_to_low)
{
if (pins_high_to_low & (1 << BUTTON_0...
Anyone to tell me where can i get the CDB file for nRF24LE01? I've downloaded the SDK and the nRF go Studio, but i still cannot find the CDB file.. Please help me to find...
Hello,
I'm trying to start softdevice on a custom board with nRF51822 chip and S110 device. The code hangs in SOFTDEVICE_HANDLER_INIT. It seems that EVENTS_LFCLKSTARTED...
