I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
I am implementing sha256 with hash message bigger than or equal to 8KB. I tried with nrf54l15dk_nrf54l15_cpuapp target, and it's working fine but if I try with nrf54l15dk_nrf54l15_cpuapp_ns...
Hello,
I'm new to this development environment and trying to get one of your projects to build for the nRF9151-DK. I recently installed everything with the latest versions...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
