Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
I'm looking to migrate from SDK 6.1 to SDK 9.0, using GCC and Eclipse. Any pointers would be welcome.
Also, I'm hoping to start using the OTA DFU. Once again, if there are...
I want to capture connection packets between BLE Master and Slave
(this part is easy) but also capture any advertisement send out by slave
at the same time.
Our BLE peripheral...
I brought up the Template example on the S110 for nrf51822 and as an exercise, attempted to add in the battery service. I just did a few simple things:
in main.c:
-included...
Hello, I want to using nrf51 dk with uart communication.
So, I want to know how connect both PC and nRF51 DK.
I've download with 5pin connector to USB.
In former days,...
hi,
i have meet an issue,when my pca10028 board was advtersing it can be found by the android app which provide by nordic.But it can not be found by my mobile phone.So,i...
I have compiled the bootloader and the application firmware with keil.
When I install the application firmware by means of the bootloader dfu ota.
The bootloader launches...
Hi,
Unable to locate the source code for "UART/Serial Port Emulation over BLE"?
The documentation for this is available in this link - developer.nordicsemi.com/.../a00072...
Hi, i try to understand how to use power down modes. But i have a problem in the example gzll_device_w_power_management of nrf24le1 sdk. Before enter register retention in...
I just started using RTT because I needed to trace execution through some ble events and the uart could not keep up.
It is very nice, but I am used to frequently resetting...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
Hi,
I'm using device manager for bonding starting from a sample application in the SDK.
I see that the DM_EVT_CONNECTION is raised before the BLE_GAP_EVT_CONNECTED but...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
I am using nRF51822-QFAA_Rev2. S110 7.1.0, SDK6.1.0.
First, program bootloader, then program \s6310\s110\ble_app_hrs\arm\ble_app_hrs_dfu code.
I use Android nRFtoolbox...
