I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hi,
Merry Christmas!
I have a question about pstorage_store.
Actually, I want to store some data in the memory. Each piece of data has its own size (between 1 byte to...
Can I config AIN0 and AIN7 as the input pins of ADC, and config P0.01 and P0.02 as TWI, and config P0.03 and P0.04 as GPIO?
Or I must config ALL AIN PINS as ADC?
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
I've followed the steps mentioned in this thread devzone.nordicsemi.com/.../ and everything seemed to work fine. I've successfully uploaded "nrf51822_beacon_app.hex...
Hi.
I read in the sdk documentation, there is a library to use MPU-6050.
So i try to find it but I did not succeed.
i want to read data from 6050 and send this data with...
Hello.
I want to use nRF51422 chips to make some kind of mesh network using raw radio stack (NRF_RADIO) with my own protocol on the top of it. In reference manual there...
Hi,
I am a new comer to the nRF8001.
I am using Redbear Blendmicro (nRF8001) for my project.
I have wrote a apps to scan my Blendmicro(s) and acquire their RSSI value...
I use direct input AIN2 pin battery 3.3v, the other pins are not connected to anything, I did not enter into ADC_IRQHandler,may ask about what the problem it
this is my...
Has anything changed with the Bluetooth LE in iOS 8? I have an ANCS library for Arduino ( https://github.com/robotastic/ANCS-Library ) that was working fine with iOS 7. I...
I'm trying to program nrf51822 via st-link and open ocd.
Here command:
openocd-0.8.0.exe -f interface/stlink-v2.cfg -f target/nrf51_stlink.tcl -c "program address".
...
dear all:
I have 2 kind of board that are PCA10006 and PCA10028,
but I find out the IoT example can't be run on PCA1006,
what are different between PCA10006 and PCA10028...
I have added the DFU service to our own project. Normal application updates work perfectly and even the update of bootloader and softdevice is fine.
In a new case we had...
I'm still newbie of BLE developer, and designing a BLE device based on nrf51822 (whose service uuid is partially used for identification of serial number).
Like nordic's...
We want to design our own custom USB Dongle for connecting our sensor board to a PC. Sensor board has a nRF51 chip using Gazell protocol to transmit sensor data and also softdevice...
