Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF9160 device . Specifically, we are looking for:
Steps to enable JTAG protection...
Can we use the nor flash on the nrf52833 soc ? currently we are keeping the DNP if we want in future i just want to know whether it will support from the firmware perspective...
Hi,
I am working on a Zigbee coordinator based on nRF52840 using the nRF5 SDK (ZBOSS stack).
My network includes up to ~50–60 devices (both mains-powered and battery-powered...
Hello,
First of all, I'm delighted to have found the beginning of eMMC support for Nordic devices as software peripherals in NCS 3.2.0: https://docs.nordicsemi.com/bundle...
Greetings,
I'm considering nRF52840 for a product. My connectivity requirements are BLE 5+ (For GATT-based communication, No requirement for channel sounding, etc), USB...
Hello Nordic team,
We are evaluating nRF54L10 for a battery-powered Bluetooth LE medical device .
We are considering the nRF Connect SDK Bare Metal option instead of Zephyr...
Hi everyone,
We recently started to add the iBeacon broadcasting to our own BLE project that runs on an nRF5340. It is based on the code from the sample of the SDK (we currently...
Hi,
We are working on the nrf5340 and our current device firmware uses the NCS 3.0.2 (i.e. nRF Connect SDK 3.0.2). We wanted to try an upgrade to NCS 3.2.1 and followed...
Hi, so my intention was to test the free subscription of Memfault with the thingy91 I created my account in nRF Cloud but the button to access Memfault is not there, I had...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi,
We’re looking for the SBOM and the official CPE identifier for the Nordic nRF5 SDK, specifically version 15.3.
We would need:
The SBOM for nRF5 SDK v15.3
The...
I am using the nRF52840DK with nRFConnect for VS Code. In Lesson 6 Exercise 1, I connected the DK to a BME280 board I purchased online. The board exposes the four pins needed...
I've been wrestling with an issue whereby I attempt to deploy an mcuboot image to a device and inconsistently I get a message that says the firmware image is not valid (error...
I am currently encountering an issue with BLE bonding logic in my application.
When a phone initiates a pairing request and triggers a pairing pop-up, I use the security_changed...
We have a custom PCB with a nRF9151 implementation supporting both LTE/NB-IoT and GNSS. The PCB has no switching regulators or any other possible noise source except for the...
Working the SDK intermediate course, L1.E1. (SDK 3.2.1 / nRF54LM20A)
After building, I select <Debug> under Actions in VS Code. I get this popup that says "Debug options...
Hi DevZone Community,
I am facing a build issue while working with the following environment:
Environment
SDK: nRF Connect SDK v1.9.1
Hardware: nRF9160 DK...
Hi,
As the subject states.
I would like to run the tests at zephyr/tests/drivers/spi/spi_controller_peripheral as intended in testcase.yml. I can verify that I have the...
Hi All,
Anyone has experience in FRAM?
I have a project which need to integrate the FRAM CY15B108QN with nRF52840. I got a weird result by using nRF silicone, but can...
Hi,
I wanted to use the `nordic-semiconductor.nrf-kconfig` and the `nordic-semiconductor.nrf-devicetree` without the nRF Connect extension in `vscode`, but they don't seem...
Hello, I am an absolute beginner with nRF9160. I have just received one development kit.
I am trying the Quick Start application for cellular modem with AT commands.
Unfortunately...
Dear Nordic
At ncs3.2.0 zephyr sample, we found uvc sample as below.
https://docs.nordicsemi.com/bundle/ncs-3.2.0/page/zephyr/samples/subsys/usb/uvc/README.html#uvc
...
