Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
Hello,
My first attempt with channel sounding.
Hardware Setup:
- Initiator: nRF54L15 DK running `channel_sounding_ras_initiator` sample (no issues found so far) - Reflector...
nRF9160, mfw 1.3.7, NCS 2.9.2
Case:
The modem first connects to LTE-M (Germany, band 3), pretty well.
Then the modem is moved into a building basement (band 8 or 20...
Hi Team,
We are using nRF54L15.
1. Is there any api to read BLE MAC address?. If yes, can please provide it?
2. What are the configurations need to make 'yes' in ...
Whenever I open my workspace or build in VS Code, the Output tab of the bottom pane opens to nRF Connect output where it repeats this many times:
How can I debug this...
Hello.
We're planning on using a MIPI Antenna Tuner in our upcoming design and I'm referencing the documentation here for the PHASE ON (1) portion
https://docs.nordicsemi...
According to the nRF9151_PS_v1.1 specification, when using PSM, the current consumption should be below 5 µA ("LTE power saving mode (PSM) floor current – 2.7 µA").
However...
I am working with the Radio Test sample, but the project does not include any .overlay file by default. I created my own .overlay file and placed it inside the boards/ directory...
Is the schematics developed by our engineer for the antenna okay?
1. Is the L6 and 0 ohm resistors are for tuning?
2. Can I remove the 0 ohm resistor and use the same...
Modem Firmware: mfw_nrf91x1_2.0.3
SDK Version: 3.1.1
nrf9151
Using the aws_iot sample as a reference, I'm trying to get my device to connect to an IoT instance that...
Hi
my customers are complaining that they have a bad connection in a large conference hall with many people.
Actually the other people in that huge room are not using...
Hi,
We are observing cellular positioning timeouts. A-GNSS is enabled and the device is provisioned in nrfcloud.
The device is located indoors, thus GNSS based positioning...
I'm using SDK 15.3 (S140) on an nRF52840 and FreeRTOS 10.
I've got a product that plays a peripheral and from time to time checks its surroundings for particular beacon...
Hi Team,
I'm on nrf52810 MCU, and am using the BLE Peripheral use case and need the BLE DFU functionality.
I've build my application on top of ./nRF5_SDK_17.1.0_ddde560...
I’d like to understand whether the ZBOSS Zigbee stack integration in Zephyr is considered production-grade. My concern arises from the fact that I’m unable to interface Nordic...
Dear DEVZONE,
We are working on Nordic nRF58480 USB dongle for Thread activities.
We are using one testbench on which we need to automate with Python scripts reprogramming...
