i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hello all,
I'm interacting with some nodes in a test network:
setup: 10x nrf52840 DK (PCA10056) boards loaded with the following software.
1x Coordinator ( Zigbee CLI...
Hello,
I'm using nRF SDK v1.6.0 with nRF9160 development board. I did minimum changes to Asset_Tracker_v2 application (enable debug log, set up for my aws account and to...
Migrating from nRF5 SDK to nRF Connect (Zephyr) what is the best way to define pin names using a custom board? in nRF5 SDK the header file custom_board.h usually defines the...
If I enable CONFIG_ASSERT=y this example will crash (or code using the DF APIs)
To reproduce:
- nRF Connect 1.6.1
- In direction_finding_connectionless_rx add CONFIG_ASSERT...
HI Devzon
currently my customer has some question about the power consumption difference between "LOWLATENCY" & "LOWPOWER" on NRF5340 GPIOTE
we useing PPK2 to testing...
hi support team，
customer have one problem that saadc is high rate sample at about 800hz, it runs ok, but after ble connection and send data to device from mobile device...
Hi , My application works on ncs v1.3.0, and now I need to upgrade the SDK to upgrade the application to work on ncs v1.5.1. I have completed the application development on...
Hi,
I am developing a PCB with the nrf52840 chip. The chip is implemented as described in the datasheet ( Circuit configuration no. 6 for QIAA aQFN73 ), using the files...
We are encountering a very strange situation. We have two custom PCBs (PCB1 and PCB2) both with an NRF52832. We were able to program both PCBs (multiple times) with the JLink...
Hi
I'm trying to file open and write for logging temperature data and others on nRF52840.
I successfully open, read and write on SD card or flash in nRF52840.
I also...
I am looking for technical support on Nordic Chip NRF52805 chip recommended footprint – BGA pad size.
Based on the application note on WLCSP Package guidelines from Nordic...
I'm moving from SDK 1.5.1 to 1.6.1 and when I recreate the project using the new version I get;
C:/Users/randall.philipson/kodiak_core_iot_zephyr/core_iot/prj.conf:88...
Hi,
I'm using nRF Sniffer as a development/debugging tool - and it's great and it's very convenient; But now I have some unusual requirements - to sniff 2 or more connections...
hi，
We use the IAR development environment，We will use like the following GCC compilation parameters ，What are their options in IAR
SP -fstack-protector RELRO -Wl,-z,relro...
Hi,
I am looking at the 802.15.4g specification which is used by Wi-SUN alliance. It uses a PHY that is different from the standard 802.15.4 that is available in all nordic...
