I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello,
I am using the n RF Connect SDK v1.5.1 and using the Zigbee Projects.
I wanted to know if and how to change the default stack profile of the Zigbee App. The following...
Hi! I am trying to interface the CCS811 with the nRF91-DK. For this purpose I am using nrf-sdk 1.6.0 and "ccs811" sample from zephyr. I created a nrf9160dk_nrf9160ns.overlay...
Hello,
I developed a code for nRF52840 Dongle to publish data on mqtt-sn topics (I'm currently using Nordic SDK for Thread and Zigbee). I need to know what are the limitations...
I'm working from the https://github.com/Martinsbl/nrf5-mpu-examples/tree/sdk13/nrf52-mpu-easydma-using-gpiote-and-registers example and the DMA portion is working splendidly...
I am trying to build the nRF Connect SDK project "at_client" that is provided with the IDE. I also tried the asset_tracker project with a similiar result.
This is my first...
i use a thread to save fil like below ,and find can not save file in sd card ,sd card SPI test ok . before enter in loop. close fil and reset system can save fil in sd card...
The first bug : I believe that the target level argument for the definition of the transition callback should be of type int16_t instead of the unsigned version since it is...
I'm trying to add a sensor driver to my project based off of Zephyr's sensor driver for adxl372. I can't figure out how to get the Kconfig file in that sensor folder to show...
Hi Nordic team,
I'm struggling with an issue where my chip wakes immediately after calling sd_app_evt_wait() - specifically if I call app_timer_start() before the wait for...
Hello, We are looking for production automated current measurement using your product Power Profiler Kit II. Is it possible to interface product using serial/commandline/python...
I wonder if anyone else has seen this issue. There are a few posts that seem to point to using nrfjprog to restore the board, albeit for nRF52. But nothing I have tried allows...
I need to do batch DFU updates, and the pc-ble-driver/nRF Connect Firmware combo is too unreliable for my needs. I would prefer to just use the wireless transciever built...
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
