Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
We developed a ble hid mouse using ble_app_hid mouse example. When our mouse used in MAC os scroll wheel function is not working as expected i.e. when we scroll there is only...
Hi, We have an issue with custom devices in the field that have nRF52811, with s112 programmed. To sort out our issue we need to connect to the nRF52811 that is an advertising...
Nordic's BLE page ( https://www.nordicsemi.com/Products/Bluetooth-Low-Energy ) says the nRF5340 is the "ideal choice" for LE Audio. I can't seem to find any information on...
Hallo,
my nRF52840 and my nRF24L01 are receiving the same data in proprietary radio mode.
Several nRF51822 are sending mixed up data.
Within the nRF24L01 - radio Interrupt...
Hi,
I am completly new in nrf52, nrf-connect and zephyr environment.
I need to configure pwm channels that wont be used to drive led...
Most of thing is undestand for...
Sending a PSK like:
AT%CMNG=0,42,3,"1r0nm@n"
should result in failure, as that is not a valid hex string (as documented in nRF91 AT Commands). Currently this results in...
Hello,
I am trying to run the CCS881 sensor sample in my nrf9160 board. I have made changes to my project config file and main.c file as mentioned in
https://devzone...
I need to compare two ble_date_time_t structs to figure out if one is later than the other. So basically I need to check if rtc_datetime > expiration_datetime. Both rtc_datetime...
I plan on writing my own service (similar to NUS) but prior to that, I'd want to use all the existing APIs for initializing the GATT and BLE stack at least
I'm calling the...
Hi Team,
i have trying to create multiple serial port with debug log enabled in the sdk code sample but when i am going to init log_init a long with any UART / SERIAL...
HI
I still try to reconfigure my Zaphyr testing environment to NRF Unity/CMock but I've encountered more issues.
1. __syscall mocking
Is there any reason to exclude...
Hello there,
I'm trying to interface msp430 (master) with nrf51882 (slave) through SPI. I'm running soft device 110 to broadcast the received data from SPI through BLE...
Is there comprehensive documentation on DFU, mcuboot, and zephyr somewhere? I have an nrf52840-based device running a Zephyr 2.4-based application with mcuboot 1.7 as a bootloader...
Hi, I am trying to interface Max31865 with NRF52832 via SPI communication. My module RTD pt100 working fine with Arduino but I am getting unchanged wrong value while programming...
Hi there,
I have used the nrf2724 (radio module) as a prototyping platform. I am able to flash my personal program to the nrf24le1 on the nrf2724 and it functions properly...
