Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log.
Hi
I have a project using winc1500 as WiFi module, base on example wifi shell example and post
I add:
CONFIG_WIFI_WINC1500 =y
CONFIG_WIFI_WINC1500_REGION_ASIA...
Description:
My nRF52 DK has stopped being recognized by my PC. Below are the details of the issue:
Kit Info: PCA10040 v3.0.0 (2023.22), nRF52832 target MCU
...
Hi
sdk:17.1 ble_app_uart(esb_timeslot))
When I was conducting the integration test between my device (nRF52832) and the external device (nRF24L), I encountered a problem...
Hi,
I'm attempting to use OpenOCD to perform the equivalent to "nrfjprog --recover", since we've recently started using that feature.
I read through this case, but it...
Version 4.20a (Win x64) of Segger's Embedded Studio has problems with it's C syntax highlighting -- specifically conditional compiled sections of code. Code that is not being...
Hi,
We are using nrf52840 to develop a cryptocurrency hardware wallet. We want that user can verify that the device is authenticate. In order to authenticate, the desktop...
Hi,
I'm using Kail and I have a project with original target device nrf52832xxAA, I need to change it to nrf52832xxAB (the device onboard is nRf52832QFAB).
When I...
Hello,
I have to send SMS from NORDIC nrf9160dk which is using iBASIS sim card to my mobile phone. For this I tried two programs (at_client and simple_at). But nothing works...
Hello,
I am trying to run https://github.com/sigurdnev/fw-nrfconnect-nrf/tree/master/samples/nrf9160/i2c_scanner exampl. It is not compiling with the zephyr right now...
Hi,
for a new project we use the NRF52480, I can get it into low power mode with a total use of 20µA ( with all the other hardware on the board ). But when I initialize...
As far as I can tell, the packet sent by nRF24L01+ PTX only contains a destination address. There if no information that identifies the transmitter (i.e. PTX).
So, when...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
When I try to receive data from terminal at that time it can not goes in uart_error_handle() function and data is not received.
Which macros are enabled in sdk_config.h...
As regards the NRF52840, I want to make sure that it is in System Off not Emulated System Off. Hence the device must not be in Debug Interface mode .
I want to retain the...
