Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi,
In my project NRF51422 need to communicate with two peripherals which are supporting only UART communication.
please help me if there is any possibility.
Thanks...
I'm use the app_button lib to deal with button event ,things go well, I assign the push ,release and long push event to button event .
But there came a situation,while the...
I have noticed that when I run in release mode, turn WDT on, write bonding info, clear bonding info, and reset, my application suddenly uses 2mA more and takes 5 minutes ...
Hi all:
My iOS app use iOSDFULibrary to update my ble.But when the device enter into DFU mode ,it disconnected for a while.
This is my log:
2018-11-27 21:00:11.122263...
Hi Nordic.
Now I am working on a BLE smart card and am adding an external power amplifier. For low power consumption, i decided to give power only when I want PCB doesn...
Hi,
I tried to use nRF52 evaluation kit to program my custom board for that I have used Debug port P19 in evaluation kit. It was working in the beginning but after sometime...
Hello,
I tried to follow the instructions in this tutorial: github.com/.../nRF52832-buttonless-dfu-development-tutorial
1) I flashed this file via nrfjprog: examples\dfu...
The power estimation tool on https://devzone.nordicsemi.com/power/ maxes out at a minimum interval of 7.5ms and a maximum payload of 27 bytes, with 824mA average current....
Hi,
We need to develop an android app that can only scan a nordic ble and send out advertisment packet in our own customised UI and format. Getting the NRF_connect android...
Hi . .
I want to read the data and sent over ble UART app (via ble )
For that I am using Twi sensor ,in order to send the data what are the changes I need to do in twi...
Purchased nrf52840-DK boards for evaluation. Tested ESB protocol example successfully using Segger environment.
1. I could not find any prints on my host screen after i...
hi.......
how to choose the slave address for peripheral device ?
i am using nrf52382 and segger version 15.2
because i want to pass the address in twi sensor
guide...
Hello, Professional,I meet a strange phenomenon,now I use the nrf52832 IC, when I use the ble_app_hrs_freertos in SDK 11, the Power consumption is nomal, The Average current...
Hi,
I am using nRF24L01P and facing issue of RF Performance varies with batch to batch of nRF24L01P with built-in Antenna. To evaluate the performance of the IC and Antenna...