Hi,
I’m trying to use the SoftDevice Controller in peripheral-only mode on the nRF54L15 (using NCS 3.0.1), but I can’t get it to build with `CONFIG_BT_LL_SOFTDEVICE_PERIPHERAL...
Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello to all
using the SDK nrf52840 trying to activate tcp client server example using soft device s140
On the server side
After the function in the main
err_code...
Hello team,
Is there a standard Nordic policy for longevity of SoftDevice updates and continued support for a device once it has been deemed "mature"? Context: I'm beginning...
Hi,
My nrf 52840 pdk and my custom pcb with nrf 52840 soc. both are running with same application ble_proximity example from sdk 14.1 and softdevice s140 5.0. when i set...
Hello All,
Chip : nrf52832
Mobile App : BLE scanner
Requirement : We want to transfer 20 Bytes(or more) at every 8 ms. Is it possible?
I have tested it :
No of Bytes...
Hi all i am facing few problem after checking the power consumption of the nRF52832 using the Power profiler kit. I followed the demo video in the link ( https://www.nordicsemi...
Could you please check whether 52840 can support memory map to QSPI PSRAM on QSPI interface?
If yes, that means the compiler would see a big RAM space of 2~8MB QSPI PSRAM...
hello，all
NRF_RADIO->CRCCNF
NRF_RADIO->CRCPOLY
NRF_RADIO->CRCINIT
If the register setting are different, can rx device recieve the message from tx device? whether...
Hi,
I use the peripheral ble_app_uart with nRF52832 (Murata module). The nRF52832 is connected to another MCU, STM32L476, via UART.
I develop using IAR, with SDK V15.0...
Hi All,
Enter to Direct Test Mode, the nRF52832 will transmit 2426MHz channel frequnicy only when set any different frequency channels (e.g. 2402MHz, 2418MHz) in the Tx...
Hello,
I don't understand why the ble_advdata_short_name_find function never return a true value. I'm sure that I send a short name because I verified this on the nRF connect...
Hello, I want to synchronize several peripherals with a central, I already tried to do it with the state of the gpiote but I did not have the expected result at the level...
Hi
I'm facing a Hard fault on the softdevice when trying to call sd_ble_gattc_write(). SDK15, SD140
I have a Multilink central connected to UART using app_uart. when a...
I have been doing a bit of searching and reading but I'm none the wiser.
I have a client that uses lots of BLE nRF51822 based modules made by Raytac Corporation in a classroom...
