Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I am trying to port my Application from SDK13.0 to 14.0.
I have completed the porting. But the code is not working.
In Service initialisation there are issues...
Hello,
I use the nRF5 SDK 11.0.0 and with it we can easily build the examples with armcc from Keil, or with gcc (arm-none-eabi-gcc) from the command line using your Makefiles...
The current configuration looks as follows:
IDE: Eclipse
Toolchain: ARMGCC
SDK: SDK5_NRF_14
DK: NRF52DK-PCA10040
I am trying to port the 'bootloader_secure_ble'...
Hi,
I've combined the secure serial and ble bootloader and using it for my custom board. I tried flashing my application hex over serial using nrfutil. I get a device programmed...
Hi,
I am working on the nrf51822 board and i am only the PAC20006 board version seems to be working on it. I am using sdk 11 and soft device version s130_nrf51_2.0.1 s suggested...
Planning for Evaluation of nRF52810.
I am thinking of using nRF52 DK for this and i want to know if there is any beacon with nRF52810 which i can use for this evaluation...
Hi All,
1.One master BLE has to connect to Slave BLE, then both device should read other RSSI and sent the data through UART.sending the RSSI should be every 200 millisec...
Hello,
I try to use those functions for printing log massages on the Segger RTT terminal, but I have many problems with that.
1. How can I use this function without printing...
Hi everyone,
I am using nRF52832 kit (PC10040), eclipse and softdevice S132 V5.0.0 for developing a BLE service. I follow the service tutorial and I refer to the code from...
i want to connect raspberry pi 2 with nordic thingy 52 via ble.....while issuing connect command after gatttool -I -b Mac addr it is throwing some connection refused error...
i want to know about how nrf51822 module's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
All,
I'm relatively new with the Nordic Ecosystem and have been playing with the example projects on the nRF52 DK and have successfully gotten several examples up and running...
Using Keil v5, ARMCC 5
Pin state equals:
Level 0 - 0x00000000 - pin low
Level3 breakpoint after read - 0x00000040
Level3 breakpoint before and stepped through -...
