hi support tean,
customer is asking about " Credential storage management %CMNG" in our modem, how to calculate the hash value
i have put the log in below:
[12:33:32...
Hi,
We designed our custom board using nrf54l05, and tried to flash it using segger J-lInk as well as using nrf54L15-DK Debuger out port using nrf connect Programmer utility...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
Hi,
SDK: 3.0., nRF54L15
The application is Matter + BLE dynamic multi-protocol + battery powered sleepy end device. Current Application(Matter/Thread + BLE + Firmware...
Hello, I am trying to develop a bluetooth mesh network with two provisioners, one being an external provisioner (mobile phone) and another being node in the network (nrf5340...
I'm developing a small IoT device that needs to retrieve and transmit its location upon pressing a button. While testing the modem using AT commands, I can consistently retrieve...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
Hello,
I am using secure_dfu_secure_dfu_ble_s132_pca10040 project. Now I want that the user who has specific key can only access the nrf my device and then can send the zip...
Hello!
Does anyone know what's the maximum frequency for SPI (SCLK) for nRF52832 or SDK 12.1? I see following code in nrf_drv_spi.h:
typedef enum
{
NRF_DRV_SPI_FREQ_125K...
Can someone tell me how the DETECT signal works in the nRF52840?
This version of the nrf52 has 2 GPIO ports.
Does that mean there are 2 DETECT signals? or is there still...
Hello, I'm using the nrf UART 2.0 app with nrf51822 and I'm wondering how a line of characters is sent using this app. For example if I write 'abcdefg' does the BLE receive...
Hello everybody, I'm new to the Nordic system and the nRF52. I'm trying to become familiar with the board and I want to be able to read different 4 input pins, each one attached...
I am using Segger embedded studio 3.1 with SD132 2.0.0 and a nRF52832QFAAB0.
I have verified that I am compiling against the correct header files. This service number for...
Hi, even if I set hal_nrf_enable_ack_payload(false) on the sender (and receiver), the receiver still sends back an ACK which i can detect in the NRF_ISR(). is this normal...
Hello,
I have a pca10028 and I am wondering if I can use it also to flash nrf52 boards.
I quickly tried with rknrfgo on mac to wipe a custom board based on nRF52832 and...
Hello.
I decided to use an external solution for RTC.
Sometimes the RTC chip offers an buffered 32.768KHz output.
Can I use this output to supply the 32.768KHz to the nRF52832...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hai
i am using mbed to program my nrf5188. now i am using securityManager to implement a bonding between central and peripheral. now i need to know when a device is connected...
Hi,
In my code, I have not started the HF clock. I call the ble_stack_init where "SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);" is called. Which HF clock...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
The ble_app_uart includes "printf("\r\nUART Start!\r\n");" and "UART Start!" cames out on the putty...
