i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
This case don't happen when i merged net_core and app_core to burn . I used to burn only one core.
What causes this?
Now I have a new question.I use one nrf5340 as CIS...
I am using nRF connect SDK and wanted to examine gpio 'out' register during the debugging session but every time I try to print the register value, I get the following error...
Hi,
I am using the SDK 2.1.1 and I will upgrade to 2.1.4 since errata 160 is fixed there.
Reading the errata document here , the anomaly 168 is fixed in SDK 2.5.1. Unfortunately...
Dear nRF support,
nRF5340 custom board
nRF NCS 2.5.x
Running into this very weird issue:
Program runs fine if I don't attach debugger to it
When I do "attach to...
Hello Nordic Engineer,
I successfully controlled the 52840 DK through Mesh using my phone. However, after exiting the app and reopening it, I can no longer control the...
Hello Team,
I’m working on implementing BLE Mesh on the nRF52832. I extracted the BLE Mesh ZIP file and placed it in the same directory as the nRF SDK. Then, I opened the...
Dear Nordic Support Team,
I am encountering an issue with the nRF52 SDK for Mesh v5.0 and nRF52 SDK v17.0.2 while running the serial example. The system runs for a while...
Hello,
In the header file nrf54l15_types.h, we see the following defines related to the SAADC:
* REFSEL @Bit 12 : Reference control */
#define SAADC_CH_CONFIG_REFSEL_Pos...
Errors on calling "lte_lc_init()"
Does anyone know what the corresponding error codes mean, or what could be done to debug the cause?
Thank you very much.
I am writing an i2s application for the nRF5340 Audio DK with toolchain and nRF Connect SDK v2.9.0.
During development I noticed that nrfx_i2s_start() does not seem to check...
Hi,
I am working on a project where I have two separate physical devices , each based on an nRF52832 :
One device is a BLE Mouse
The other is a BLE Keyboard
My...
Hello, lte_ble_gateway works ok using dk91 or thingy:91 on, v251 - ok v262 - ok but not on, v270 - err v280 - err v290 - err This is straight example code as found in VS....
Hi Team,
I need help currently we are using nrf52833 micro controller, we have problem with external clocks. we want to disable external 32Mhz and 32khz clocks and use only...
I’m using an nRF52840 powered by a coin cell (3V nominal, dropping to 2.3V) and need to read a K-type thermocouple . The challenge is finding an amplifier that:
Operates...
