Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hello
I am working on the NRF51DK i would like to monitor the battery percentage and notifythe value over the air to the user and aslo alert the user if the battery levels...
I have to develop my own Dfu central to update my nRF51822 peripherals over the air.
Could you provide sourcecode for one or more of your Dfu central applications like: ...
I ve already found this post regarding the AutoConnect Issue.
devzone.nordicsemi.com/.../
I have the same problem with a Sony Xperia Z on Android 5.1.1 ...
Is there...
In previous SDK (or softdevice?) version, the maximum data length for a notification was 20 bytes .
With SDK V10 and softdevice 8, the following code returns error NRF_ERROR_DATA_SIZE...
Hi, I have implemented a music control button.
This button can send (volume+, volume-, play music, stop music and my custom control (0x06) for my app ).
Procedure:
...
Hi, im trying to update the firmware of a nrf52 using dfu ble. For example, have a blinky example running and switch to a blinky2. Can anyone know if this is possible?
Hello,
I am doing a search in the Eclipse to find texts, I noticed that Eclipse is not finding any of the texts from the Include files. I did a google search on this issue...
Hi,
I use pstorage to allocate 32bytes of memory with 2 block, means each block having 16 bytes, when I write 16byte data into block_0 portion, I am not able to go to the...
Hello,
I use the Segger J-link software with my PCA10001 and recently updated it to last version (v.5.1). After install it asked me to update the firmware to the last version...
Hello,
I'm trying to flash external nrf51422 module.
I want to flash both softdevice and application. I used below commands:
mergehex -m %SOFTDEVICE_NAME% %APP_NAME...
I want as much control over advertising as possible. Barring that, I want to understand why the softdevice automatically goes back into advertising after a GAP disconnect...
Hi,
Assume that we want to send a data array by putting it in consecutive advertisement packets. I know that data update has to be done by calling ble_advdata_set(...)...
Hi
I'm trying to implement battery level on my custom profile.
So I used battery.c and ble_bas.c files for the battery service from nodic's sdk nrf51822_v4.4.1.31827....
I have make over your bootloader example to create my own without BLE support in bootloader (new programs are send in application instead of in dfu bootloader). Bootloader...
