Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
Do anyone ever measured current consumption of ble_app_uart?
What is current when connected and uart idle, transmitting, receiving, and transmitting while receiving?
Please...
I tried changing the define below from 1 to 2, so I could have one handler for a button and a different handler for other sensors. But my problem is:
If I set it to...
Hello,
I've developed a circuit with Mikroelektronika's nRF T click module. This module uses nRF24L01P but as I see I cannot order it because it is obsolete.
Should...
We plan on use the ST BAL-NRF01D3 balun for a PCB with both an nRF51822 and a nRF51922 on the same PCB separated by about 4 inches.
Should we use the PCB antenna as on...
Hello.
I am very confused with memory layout of nrf51822 BLE examples using SoftDevice stack.
Some examples set IROM1 range from 0x0 to 0x3ffff. (ex, ble_app_advertiseing...
Hi,
I have a nRF51422-EK board (Rev. 1.0) that is bricked.
When connected the LD3 is on.
Jumpers are present on P8 and debugger.
Device manager (win7) assigns...
Hello,
I was puzzled by RM.
I notice POWER control register in peripheral(UART,SPI,TWI) module.
Please answer following questions about the relation between system...
I download the softdevice for PCA10001. And I want download another program, but it didn,t work. The problem I have attached here. As you known, I have push the button 'recover...
We plan on using the external 16 MHz and 32 KHz oscillator inputs to reduce BOM costs since our host micro uses a 16 MHz and 32kHz crystal and it can generate outputs. If...
Hi guy:
I have buy nrf51822 dk .Why I can not download nRF UART App for Android 4.3 at below page www.nordicsemi.com/.../nRF-UART-2.0-for-Android-4.3
Thx
I made code like to below for using 16Mhz system clock.
/* Start 16 MHz crystal oscillator */
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0; NRF_CLOCK->TASKS_HFCLKSTART = 1;
...
Hi guys,
I have designed a custom board with nrf51822. Data transfer seems OK, when I do it through Master Control Panel - I can write data to characteristics and I can...
Hello
I'm planning to use the nRF8001 SCC with an external microcontroller. So far we have purchased the nRF8001 sdk and the nRF6700 Started kid. My question is simple...
