I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Would you recommend purchasing Red Dear Lab Development Board? Or should I get an EVKIT from Nordic Semiconductors?
Nordic Semiconductor eval kits are expensive and shipping...
I want to have it wireless capabilities into the cable, the receiver and transmitter antenna ports with shielded wire connected directly, so there will be a wireless signal...
hi, guys.
I'm prepareing the Korea certification, KC, with nRF51822 BLE system.
I'm progressing to get KC by certification agency.
Today, They will have RF signal test...
I was comparing the binaries for the S120 and S110 stacks and see the MBR is different.
I was under the impression that the MBR never changes and was thus expecting it...
Hi Nordic
We want to test radio parameter through IQxel . Now,we need a application software to control nrf51822(TX,TX,outpower,channal and so on ) . Can you recommend...
I'm using the example code for simple device/host Gazell in SDK 7.1.0 as my starting point for my application.
My program runs for a second or two, then ends up in the...
Hi
I am new to programing low energy devices. I got a Blend Micro from RedBearLabs. I am using the
nRF Master Control on android to connect to it. I am able to change...
As I create my first 'profile document', it would be nice to read over some examples. My only knowledge of this document comes from nAN-36, section 2.2.2.5 :
A profile...
Hi
in the SDK 7.1 examples, there are examples about how to use the hardware peripherals, and examples on how to use the BTLE stack, but nothing combined.
How do I combine...
Hello, I've started bluetooth development with nRF51 DK since yesterday.
My devlopment platform is KEIL-MDK(v5)
Yesterday, I just tested my board, download the blink...
I have an nrf51 dev board which i can currently connect to an android phone and read data from. I would like this board to be able to scan for other BLE devices and send data...
While attempting to understand why my S120 v 1.0.1 application aborted in:
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, assertion_handler);
producing:
ASSERT...
In regard to the following functions
uint32_t sd_nvic_critical_region_enter ( uint8_t * p_is_nested_critical_region )
uint32_t sd_nvic_critical_region_exit ( uint8_t...
Hello, from looking at the GCC linker files I take it that S120 softdevice doesn't support using the full 32KB RAM of the new nrf51422-xxac devices. Is this something that...
Hi, I have written a simple program to calculate the number of retries with nRF24L01+.
On transmitter side, maximum number of allowed retries is set at 1. The transmitter...
