I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
To people who might be interested in this ticket
I'm trying to make a WiFi connection using the nRF7002 chip. It is a custom board based on STM32 chip. My question is, is...
example:ble_app_uart+ esb_timeslot SDK17.1 Hi Recently our product (PRX) received poor esb communication. I caught through sniffer that when PTX sends a message, our device...
Hi, I have gone through Lesson 4 in Wifi fundamentals. But exercise 1 fails to compile. I have also tested to compile the solution-project, but with the same result. There...
When I look at eh graphic .overlay, I see that the UART0 is there, but no node is assigned. Is there a Node for a two wire UART Driver with no flow control? Peripheral only...
Hello,
I bought a new USB keyboard and since i can't detect anymore Nordic Devboard as nRF5380. No device detected on Visual Studio Code, and on nRFProgrammer neither. ...
Hi,
I working on a project where i measure the distance between nrf52840 dongle and nrf52840 dk using multi carrier phase difference method.
Now, i want to display the...
Hello.
I'm currently trying to send AT Command using an external MCU or USB to UART to check LTE on the NRF9160. The board I use is the nRF9160DK. I changed the pins of...
HI,
I have two solar panes for my project 3W 5V and 2 W 9V. I would to measure current of the panels with the Power Profiler II.
I think this should work (my calc is 3W...
Good Evening!
We are designing a project using BLE; however, it requires quite heavy processing. We are still at a low level with pure C to save power, but the MCUs offered...
Hello,
Looking for potentially a better way of un-provisioning a provisioned mesh node. My nodes are provisioned via NFC, tag data containing UUIDs & OOB data. After the...
I work nRF52840 + nRF5 SDK(S140 v7.2.0)
If I call sd_ble_gap_connect() for a DeviceAddress of an already connected device, what will be the result?
What will be the error...
