I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello,
I'm designing a custom board with an nRF52840. I currently have an nRF52840 DK (PCA10056, v3.0.1) and would like to use the on-board debug out header (P19) to program...
Hello,
how can I increase the number of ZBOSS buffer (zboss_api_buf.h)? Currently they are 25.
We are using nrf52840 with nrf5 sdk for thread and Zigbee v4.2.0 without...
Hello,
I need to use timer1 in counter mode.
how can I use GPIOTE to start the interrupt of the timer( NRF_TIMER1->TASKS_START = 1) ?
when using directly the nrfx timers...
I try to add a custom signature key to the nrf5340_audio application from NCS2.7.0. I cannot use an absolute path because the project must be build-able by different people...
Hi,
I am carefully assessing the life cycle cost to define my strategy of launching 4 product models in the market by next year that they are in design stage at this moment...
Hi all!
I am having trouble intalling the nRF Connect SDK in my Windows 8 computer. I'm currently following the installation steps specified in the nordic course https:...
Hi,
I am currently working on a project using the nRF52832 as my controller. During development, I realized that both BLE central and peripheral roles are necessary. I searched...
Hi,
I am currently working on a project using the nRF52832 controller as a gateway device and the nRF52810 controller as a timer indication device.
I have successfully...
Hello,
I am a student currently studying Bluetooth Low Energy (BLE).
I am working with two Adafruit nRF52832 boards (Adafruit Feather nRF52 Bluefruit LE - nRF52832, link...
Can nRF51822 be used as uart BLE peripheral together with nRF52832 (as uart BLE central)? If so, are there any examples? So far I can find only uart ble example for nRF52832...
Hello, in a video by Ai Kevin of Nordicsemi sharing about ESB development, I learned that the ESB can be specially configured to work with Ellisys Bluetooth Explorer for packet...
Hi, Is it possible to use the same UART instance for app core and net core to put the log messages? I am using an nRF5340DK board, which uses a separate COM port for each...
Hi,
My phone can find, but is unable to connect to, the FastPair locator_tag example. I have made no changes to the example code.
The most relevant error I can see in...
I would like to reduce the power consumption in normal operation mode.
Then I would like to reduce the operation frequency in the I2C, SPI and UART.
What is the command...
Hello everyone,
I’m trying to set up an nRF52840 dongle as a Thread radio co-processor to integrate with my Home Assistant setup. I followed the instructions in this Nordic...
