Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
We are in the process to add spectral sensor to zephyr based BLE sample, but following the tutorial to add overlay or copying other sensor configurations not helped much....
It has been said that Nordic SDK v4.1.0 for Thread is in maintenance mode. I was told that I should move new Thread development to nRF Connect SDK. I am trying to explore...
Are there any examples of libuarte enabling both uarts in the nRF52840 at the same time? I have been trying now for a full day and keep having problems with what options to...
Hi,
I have an app based on freertos_hrs example (nRF52832, SDK14.2)
I'm trying to get it into low power(sleep) mode, however the idle task keep on running and the system...
Hey all. I was testing DFU over USB on an nRF52840, SDK 17.0.2 and I can't seem to get the actual application to run after a successful DFU. I generate my own keys, use them...
Hello,
SDK51 appears to be an inconsistency with how various BLE related events are handled in the SDK. Multiple BLE event handlers may be registered using the NRF_SDH_BLE_OBSERVER...
I'm currently implementing a DFU "controller" in C on the nRF9160 for performing serial DFU with the nRF52840 and believe I have discovered a bug.
My firmware image was...
Hi
I'm using nrf52 DK with SDK V17.0.0
Currently, I'm using Single Buffer to send Data through BLE.
However, I want to use Double Buffer instead of using Single Buffer...
I might be dense here, but please bear with me and clarify something. I am looking at the SPI bus as drawn on the nRF52840. According to the schematics (PCA10056 - nRF52840...
Hello,
Background: I have a custom board that contains nRF52832 module and exposes UART pins (RX, TX, RTS, CTS). I have developed an application using nRF5 SDK v17.0.2....
I'm using SDK 17.0.2 And I found that when the Scan timeout is not working,
Debugging I found that when the nrf_ble_scan_on_timeout function is called, the source of the...
I have an nRF5340 development kit. I can flash a custom application into the app processor. However, when I try to flash the peripheral_lbs sample, I'm getting the error shown...
The hrs.c has the following code.
/* Heart Rate Service Declaration */ BT_GATT_SERVICE_DEFINE(hrs_svc, BT_GATT_PRIMARY_SERVICE(BT_UUID_HRS), BT_GATT_CHARACTERISTIC(BT_UUID_HRS_MEASUREMENT...
I have added the following modification to "ble_app_hids_mouse" example for pca10040 s132.
I want to add a peer whose IRK is known as follows,
void peer_add() { memcpy...
Hello, guys.
We are have nRF52840DK board and Zephyr NCS 1.4.2 development environment.
I am trying to include two PWM channels in the code and control them independently...
