SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi Nordic,
I am using the example in SDK15, ble_central_and_peripheral -> ble_app_interactive. After being connected to a device, and after pairing. I am trying to make...
hi......
i want to sense the temperature and send data to the uart app via ble ... so i want to merge two programs uart and twi sensor
i have tried but it shows error...
Use central-peripheral programs. First advertising and then scan. It was found that during the adveristing the program was running normally, but the adveristing signal could...
Hi:
How to get sine_table[] data,like this.
int16_t sine_table[]= {0,0,23170,23170,32767,32767,23170,0,0,-23170,-23170,-32768,-32768,-23170,-23170};
NRF_I2S->TXD.PTR...
Dear Nordic Team,
Thanks for supporting.
I am working in ble_app_uart_c example in this example is automatically connect with its peripheral. But i need to connect and...
Hi Nordic,
Here is my configuration:
HW: Customize nRF52840
SW: blinky_rtc_FreeRTOS_pca10056
Problem: The led blink for a few sec and the board went into vPortSuppressTicksAndSleep...
I have a nordic nrf52832 dev board acting as peripheral and my client device is huawei honor 9 lite. I'm trying to send two packets (or 45 Bytes data) in one connection interval...
Hi,
I want to know how to send data with 52840Dongle with ble to the mobile, I tried to use the "ble_uart" program of 52840DK, I followed a tutorial, performed a full erase...
Hi,
Is there out of band data available for the Rx path? I want to make sure there is no interference from other bands and if a filter is already implemented in the IC RF...
Dear Team,
I am using NRF52840 for ble_app_beacon and working fine. Now I want to extend the range using 'PHY_CODED' option. Please let me know in this ' ble_app_beacon...
Hi Nordic team,
nRF Mesh is a very good smartphone App for BLE mesh development & Testing. Currently we are running mesh code on one 52DK and use GenericOnOff model to simulate...
Hi. I just started with nRF52840.
When I use J-flash for STM, normally it proveds 'secure chip' as below.
But when I choose nRF52840, I can't see 'secure chip' activated...
Hi. I just started development with nRF52840.
Press "Setting' button, it shows me "The selected device "NRF52840_XXAA" is unknown .......
And actually it doesn't have...
Hi.
I just want to test mergehex. So I put message as below.
mergehex --merge s140_nrf52_6.1.0_softdevice.hex direct_test_mode_pca10056.hex --output out.hex
Both s140_nrf52_6...
Can anyone give me tips on how to get the SCK to LRCK ratio of exactly 32?
I'm having a distorted audio problem with the TFA9879 amplifier, and the status register is reporting...
