I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi~
I am developing door sensor system using nRF52840.
Currently for power consumption, sensor (nRF52840) is system off(NRF_POWER->SYSTEMOFF=1).
nRF52840 can wake up...
Hi, I have 8 peripheral devices each one has at least one sensor attached to it( peripheral will be nRF52xx), the sensor has a sampling period of 8ms. I will be using android...
Hi,
In BLE mesh v3.1.0 I see a file debug_pins.h. For what these debug pins are used and can I disable it for my custom board?
And one more thing related to PA and LNA...
Hi,
We are currently developing a Sensors/USB/BLE/LTE-M1 product for a customer. The board is equipped with one nRF9160,for cloud communication, and one nRF52840, with a...
Hello, I am using nrf5832 with SDK 15.3.0. I want to filter peripheral device based on mac address. I modified example code "\examples\ble_central\ble_app_blinky_c\pca10040...
I'm facing problem when I want to stop receive task, event EVENT_RXTO came at long time period. 4 to 5 baudrate bytes.
Is trere any documentation where could read time between...
Hello,
I want to develop a data transfer service which has a control characteristic that is used to write commands on the phone app and if the command matches any command...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
Hi, I'm using a PCA10056 DK board to start new development. I try to program DFU secure bootloader and SoftDevice using nRF Connect 3.0.0 My issue: - configure both hex files...
Hi All
I am recently working on CSAs (Channel Selection Algorithms) in BLE on nRF52840DK, and I am using Zephyr to develop them. I have 3 nRF52840DK, one as sniffer, the...
Hello, I've developed a BLE Mesh Network using the NRF MESH 3.1.0 SDK and the nR5F SDK 15.2.0. My network has 1 client node and max 63 server nodes: I'm using the generic...
I've been developing a solution that utilizes Mesh DFU along with the Mesh Bootloader. However, I've been seeing a frequent issue where the DFU aborts prematurely due to missing...
Dear DevZone,
I'm trying to use the Seeed CAN BUS Shield V2.0 (MCP2515) with the nRF52840 DK, but the library provided is written for Arduino One.
Do you know if any already...
