According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi, I'm using the nRF52840 Preview DK to get data from a digital microphone via a PDM interface. I'm using a clock frequency on 1.032 MHz to activate the microphone. The data...
Hi,
As discussed in this ticket we need a way to reduce the current consumption.
The LPN example doesn't solve this for us.
Our application is based on the light switch...
Hi, we have the latest Xcode installed on our new development Mac (up to date iOS too).
When we downloaded the iOS nRF toolbox from git hub today we get errors when compiling...
Hello Everyone,
I am looking for an Eddystone example. It should be used for an nrf52 with s132 SoftDevice (programming with nrf52 Prev Dev Kit).
Thanks for help
I'm struggling with how to properly identify an unprovisioned mesh device. Basically when i scan for unprovisioned devices from my iOS app, I'd like for only our devices to...
If I use sdk12.3 pca10040 S132
softdevice is s132_nrf52_3.0.0_softdevice.hex
How do I determine what version of Bluetooth it is?
In SDK or where the document has instructions...
Hi, I had download the nRF5_SDK_15.3.0_59ac345,but I couldn't find the softdevice S112 hex.(Nordic52\nRF52_SDK_Source\nRF5_SDK_15.3.0_59ac345\components\softdevice\s112\hex...
Hi ,
We have the following setup :
One nrf52840-dk acting as a multi-link central
One nrf52840-dk acting as a peripheral ( blinky app )
Both communicate well over...
I want to expand the Asset_Tracker example by adding the possibility to send data through UART2 to the controller and then to the nRF Cloud.
I am unable to find any document...
for 52840, customer want to have a part of flash, it can set write protect, to avoid illegal erase or destroy, they use this part of flash to run boot-loader, is it passable...
As far as I could see, only GGA NMEA sentences are enabled by default. I want to check if RMC sentences deliver positions faster, and in my prj.conf I do the following:
...
I got an nRF52 DK and I was unable to recognize the JLINK driver by connecting to my computer via USB. My SEGGER version is 6.44E and my own jlinkV9 is normal. How can I solve...
hi all ,
now , i need add create mqtt ble gateway .
it compiler failed follow message :
C:/temp/ncs/zephyr/drivers/serial/uart_nrfx_uarte.c:1272:9: error: 'DT_NORDIC_NRF_UARTE_UART_2_LABEL...
