Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
What is the easiest way to use Arduino libraries into nrf52 projects in Keil on C?
Arduino has a lot minus : bad ide, not support debug mode, not optimize code size. But...
I work with nRF52832, based on SDK 14.0.0, and I have done DFU operation successfully with nRF connect on iOS, but when I used Android phone, nRF connect couldn't start DFU...
ble_app_gls_pca10056_s140.hex
Hi,
I am new in this field and i am trying to do current measurement on the nrf52840 PDK using PPK, in sleep mode(sd_power_system_off) i...
Hi,
I have just bought an nRFGo Motherboard (nRF6310) to develop for the nRF24LE1 (nRF2722). I was able to run some example code on the chip like toggling a pin. Next I...
Hello,
I have an application based on SDK 11 and Softdevice v2.0.0. Also there is a legacy bootloader from SDK 11 for performing DFU.
I am wondering whether it is possible...
When I run the UART app nRF5_SDK_12.3.0_d7731ad\examples\peripheral\uart in debug mode, the disassembly window opens, and I seem to get stuck on the second instruction. Step...
I am using a nRF52 and I have to measure two voltages:
the first continuously
when a command is received, the second voltage have to be measured and then...
Hi,
I flashed my nRF52840-PDK with UART/Serial Port Emulation over BLE program. Everything seems to be ok and I can connect with board via Android application. Next I would...
Hi!
I try to send data using advertise PDU and I need use custom 128 UUID.
How to convert to right format service_128_uuid and replace 16-bit value to init.advdata.p_service_data_array...
I'd like to use the nrf52832 as a mesh switch with battery powered. But I didn't find any sample code for the Low power feature in current mesh SDK v0.10.1. Does it support...
Hi,
Dear Nordic experts:
I encountered with a couple of *** issue while configuring SPI port on nRF52832 with PCA10040 demo board. Here I wrap up as below:
First...
I write NRF_UART0->ENABLE = 0x00 in my app in first line code, but now nrf51822 can connect but cannot Download and erase;
in keil it report:
**JLink Warning:...
Hi I am new to Nordic Development. I am developing a product that will use the Rigado BMD-300 module (nRF52832 but no need for FCC compliance testing). The evaluation board...
