Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I test ble bond with 'ble_app_gls' in sdk 12.3.0
eg.nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_gls\pca10028\s130\arm5_no_packs
my phone is meizu mx4, android...
I feel Slave Latency is unnecessary.
For example :
Connect Interval is 100ms,
Supervisor Timeout is 4000ms.
So the Slave Latency must be 39.
if I set Slave Latency...
Hello,
When using extended ATT_MTU without DLE, and the MTU is larger than the LL data length, I know that the MTU is divided into smaller LL packets when sending.
But...
Dear Nordic Devzone,
I want to run an Arduino Ethernet Shield with the Wiznet5100 on the nRF52840. I was wondering if there was an easier way to do this then having to...
I am designing the BLE solution using nrf52832 . The board will be two layer board with solid ground plane in the bottom layer and signal and ground pour in the top layer...
what is a valid publish handle, when I run pb_remote_client, first I input "1" and one pb_remote_server device has been provisioned, and then I input "233", it happens "MESH...
Hello,
I used translation software.
I am measuring current consumption.
I supply it from an external power source.
I connected the SB 12.
After that, I supplied...
Hello,
I'm having trouble to work on the nrf52832 DK with the accelerometer.
First, I tried to wire the accelerometer as I was wiring it on a Arduino Uno but I couldn...
Hi everyone, maybe I'm wrong but I think that the Garmin oregon 600 uses a ANT+/BLE chip made by NordiSemi, it's possible to know exactly which one it is?
Thank you a lot...
Hello,
i'm trying to DFU from 13.1 to 14.1..
What i have tested is flash(SD + B) + dfu(APP) on both versions. Now i'm trying to DFU all from sdk13.1 to 14.1.
Is it...
I know that latest nRF5 SDK and nRF mesh SDK support SES, it's really a good news for developer. I'm just curious that, can I use SES to flash SoftDevice on macOS? If so,...
Hi;
I am using NRF52 DK(pca10040) board nowadays with sdk 14.0. I read a blog post about power consumption in nordic webpage.( link )
In this blog post, there is a webpage...
I´m currently developing ble peripheral application for the nRF52832 with SDK v13.0.0. I need to have a secure connection between the nrf and android or ios mobile device...
Hi There,
i am new to nrf51822 and new to program this kind of controller.I searched over the website, I couldn't find a good introductory documentation for programming the...
