I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I have some code that used to compile using version 2.5.2
I'm trying to move to 2.7.0 and have my own manager for TWIM that needs to intercept the TWIM interrupt.
In earlier...
I'm trying to use littlefs in Zephyr with SDK 2.7.0
My code is based on the example project "littlefs" and it compiles without problem using SDK 2.7.0
I'm using nRF Connect...
I am experiencing an issue with my board, where I have interfaced an nRF52840 with an LSM6DSV16 via SPI.
The nRF52840 chip, once started, can decide whether or not to...
I am trying to get an LED attached to GPIO to turn on. I have tried all documented methods I could find but with no success. I have no issue controlling the onboard LEDS but...
Having trouble creating the zephyr DTS DTSI files for i2c0 for the nrf54L15. need to get the initial definition correct,
actually using dtsi
& i2c0 {
compatible =...
Hi everybody. I'm using nRF Connect SDK 2.8.0. I've implemented Zephyr RTOS' core dump functionality on my project. I forced the SoC to write the core dump data on its flash...
I am working on a custom nRF552832 board. I need to use the reset pin (p0.21) as GPIO input.
I am using the NRFConnect plugin on VSCode to develop and program the board...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The USB pin connections are designed based on the nRF9160-DK's nRF52840 reference....
I would like to be able to open a bash prompt with the nRF Connect SDK (NCS) v2.0.0 toolchain environment loaded without going through Toolchain Manager ("open bash" option...
We are evaluating the nRF5340 chip for a Bluetooth LE audio broadcast streaming application.
Is it possible to use adaptive frequency hopping with the BLE audio network...
For the RADIO peripheral of the nrf52(840), if you set up the radio to receive coded Phy transmissions, I have the opportunity where I can set the MODE for 125Kbps or 500Kbps...
I'm trying to use nordic's BLE sniffer on a nRF52833-DK. I have programmed it with the firmware "sniffer_nrf52833dk_nrf52833_4.1.1.hex".
I've then tried both the command...
When I use nRF Programmer on my laptop (v3.0.7) to update firmware on my Thingy53 with a USB cable and SW2, the programming seems to finish normally, but it prints "Bluetooth...
Hi, I'm having Bluetooth LE peripheral nus code which works fine with v2.7.0 with nrf52840DK (I can connect with an Android App and stream data etc): Changing the build configuration...
