I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
i am new to the topic and am looking for tutorials, additionally to the nordic examples and this community.
I found the following website:
https://embeddedcentric...
Hi,
When a board is connected to debugger, It works well for 2 hours.
But when it is detached debugger, It looks like stuck to POWER_CLOCK_IRQn after 4~6 min after power...
Hello,
I'm trying to make a one-shot MQTT publisher and I'm able to get 22 messages published but every time I try to publish the 23rd the code hangs in mqtt_transport_write...
I'm not able to get a response using the new CONEVAL AT command. I'm using firmware v 1.3.0 and a recent B1 variant nRF9160. Response is always ENOEXEC. I have tried before...
Hello,
In my project, nrf_drv_gpiote_in_init is used 3 times.
battery measure
sleep trigger by motion sensor
wake-up trigger by motion sensor
After 3rd call...
HI
I am trying to interface ads1231 with nrf5340. Regards I need to know about Gpio read. Because ADS1231 gives digital output. I don't know how to read actually. Kindly...
What is the purpose of the ble_advdata_encode() method?
I see it has been used in the beacon example, but some other examples don't use it.
In both case, the advertising...
Hi, all..
An error occurs as soon as it connect and disconnect through advertising. Timer interrupt is currently running on the main function..
and then I found error...
OS: Mac
I installed nrf v1.2.0 and Segger Embedded Studio v4.42a. I can't open project and it causes error.
I can open projects with this config on SES v4.42a and...
Hello,
I installed Segger Embedded Studio v 5.34a following the online instructions AND the Getting Started Assistant instructions for a Mac. I then tried to import a project...
Hello everybody,
I'm trying to develop mesh network with zephyr, but the problem is that logs are not displayed in SES debug terminal. In autoconf.h file I can see that...
Hi,
I have been following this post and did all the steps instructed by , but I failed to receive a response in Tera Term in the end. I have also tried changing the hostname...
Hi,
Need help to interface nrf9160 with MSP430.
Making Project where MSP430 will collect the data from ECG sensor and sending to nrf9160 in packet form. nrf9160 will going...
Hi,
Time to time, Our board stuck in QDEC_IRQHandler.
1) In which case QDEC_IRQHandler could occurs?
2) I want system reset from QDEC_IRQHandler automatically.
But...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
During development, I was wondering about advertised packets.
I thought that the advertisement packet...
