I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi,
I'm working in a project where we try to implement an Isochronous broadcaster using timeslots, co-existing with Softdevice controlled Scanning and Connecting. We use...
Hello!
I use the latest versions of sdk v17 and nRF52DK, nRF52840.
I refer to examples written by others as well as basic examples of SDK. But I don't know if I can...
I had a BLE central application and need to migrate now to peer_manager to have the LESC security.
I am using as a reference the Experimental: LE Secure Connections Multirole...
Hi
Does the SLM application turn off the UART? I need the UART to be turned off whenever its not in use due to power consumption.
Still, the modem should be on to support...
My custom board with NRF52810 doesn't have an external LF clock, so I am using Synthesised Option.
as per my knowledge clock source will take 320 uA (~200 uA for HF clock...
Hello,
i have been struggling with this issue for several days now, maybe due to my limited knowledge of thread networks.
I'm developing a solution where some devices...
Short version:
- Can you enable debug output in the mbedtls used for DTLS in OpenThread, available through the nRF SDK? If so, how?
- Can you at all chan ge the list of...
To the kind attention of Nordic support team,
we are using secured gazell library in our devices. We would like to pre-pair couple of devices (host-device) using valid secured...
Hi i am working on project where i need to store logs on flash, i included nrf_storage and set start address 0x42000 and end address 0x50000 according to my application, my...
Hello. I want to use nRF52810 as a connectvity platform connected to OpenWRT MIPS based board via UART. For some reason the only solution I can assure is to use 2 wire UART...
Dear Nordic support,
We are using SDK5 15.2.
Our application uses FDS to maintain configuration. One issue is that we have to change the configuration via phone app regularly...
Hi,
I am working on nRF52840 DK . C:\Nordic\SDK\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\peripheral\ uart I am sending data from Arduino and showing it on PuTTY...
Hi All:
I try to create a custom Characteristic,with nrf_ble_qwr,
but when set is_defered_write = 1;
connect with NRF_CONNECT APP, I can't write under than 20 byte,if...
Hi, we just saw that %BSKGEN was added in MFW 1.2.1. However, it is not clear to us what is the intended use of it. Could you please give us a bigger picture of it?
Is...
