the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi. I'm writing my own libraries for nRF52832 and I can't get UARTE to work.
Here is my code.
I'm using pins 6 and 8 as the UART example.
I wrote same code for UART...
I'm beginner with nrf chips.
I have a custom board with ntf52840 module. I connect board to stlink via swd interface, then check:
st-info --probe Found 1 stlink programmers...
I would like to perform observer role scanning i.e. passive scanning. I am using nRF52832, S132, SDK 15.2.0. I am trying as follows.
NRF_BLE_SCAN_DEF(m_scan);
static...
I am using the SDK5 development kit with Segger for a BLE application.
I found the Service for SES but the SDK doesn't seem to include the Pulse Oximeter service.
I would...
We are developing hardware to work as a AirMouse (Gyroscope based working mouse)
I am using SDK16.0 SES
I have seen that HID Mouse example
and i implement gyroscope...
I have bought a BLE Micro. ( www.seeedstudio.com/Seeed-Micro-BLE-Module-w-Cortex-M0-Based-nRF51822-SoC-p-1975.html) 1. I downloaded "nRF Connect App for Android" on the phone...
Hi there,
I've recently purchased an nRF52840DK with the 52840 SoC and I'm wanting to develop Bluetooth Mesh apps.
I'm on Mac OS X. Should I begin with the nRF52 SDK or...
Hi,
I just got the brand new Thingy:91 and would like to program it with an application earlier developed for the nrf9160 DK .
Further I'd like to use the Link Monitor...
Hi All,
Recently I have been working on nrf9160dk board. The use case is to have nrf9160 work as a serial LTE modem with GPS functionality. I have the following link https...
Hi,
I have implemented my own Vendor model, using the light switch client/server as a starting point. The model allows to send byte arrays. Since I have used the generic...
I am using SDK v16, SEGGER to program on my nrf52832 SOC for our project. I need to save a few variables to the flash memory. These variables will hold the status of the device...
Hello,
we are using SDK version 15.3 and mesh SDK version 3.2.0, on a nRF52840 DK board using the Segger Embedded Studio IDE version 4.52 (64-bit).
Our goal is to add...
Hello,
I followed this tutorial in order to familiarise with the code and understand better what is going on. Now, my question is the following, regarding challenge 2 :...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
I notice that Thread examples with Softdevice (nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried...
