Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi there,
I have added my custom services in the peripheral dfu_template example.In the advertising UUID array(m_adv_uuids),i included custom service UUID but not the...
A question about the power saving modes PSM and eDRX. A device is mostly in deep sleep and wakes up cyclically for mobile communication. It is better: Completely disconnect...
In our project, two nRF51840 will communication with each other using BLE. One nRF51840 act as central and another nRF51840 with act as peripheral. The central nRF51840 will...
I have a couple of NRF51 parts. They're pretty common at hobbyist stores still. Recently I pulled out the NRF51 dongle, downloaded the recommended Segger Embedded Studio,...
I have managed to get working a BMW iDrive to act as a bluetooth mouse for my iPhone. To do this I used a CANBUS shield connected to an arduino NANO and an nRF51 BLE connected...
Hello,
Mesh SDK 4.0.0, PCA10040 x2
I want to develop next models:
Scan server: Waiting GET message with arguments, scan BLE beacons and reply STATUS message with results...
Dear Nordic Team:
Now I am doing a example test, with nRF52832 I want to use SPI master and SPI slave transtission.I have saw many demo example,but i dont know that which...
I don't know how it feels if you visit a page that takes six seconds to open.
Isn't the profit ability of the Chinese region enough to allow you to build a normal acceleration...
Hello,
I am working on nRF52832 chip using SDK 15.3.0 in segger embedded studio.
I implemented DFU in my application and it's working properly.
But my problem is when...
WHAT is missing from my profile which prevents me from opening a private ticket?
The location? when I type it in, your profile doesn't save it (it just ignores it).
Ubuntu18...
I have successfully compiled the GPS sample. I am trying to program the device using SES and only beign able to do it when the device is previously erased with NRF Connect...
Hello,
I am using nrf52840 to communicate with PAC 1710 sensor via TWI interface. The nrf52840 is the master device and the PAC chip is the slave device. Without SoftDevice...
I just updated to Segger 4.42a to follow the recommendation in the release notes for SDK v1.2.0
When I do a rebuild the AWS fota sample I get linker errors as shown below...
Hi,
I have a Laird Development Kit for the nRF52840 (DVK-BLL654PA-R2.0) which I want to program. Unfortunately Keil uVision and nRFgo Studio have problems with programming...
